RTI Piranha Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 181

RTI Piranha Скачать руководство пользователя страница 145

5. Measurements with the Piranha System

Tube Current Probes

2014-06/5.5C

141

Piranha & QABrowser Reference Manual

5.8.2

MAS-2, Non-invasive mAs Probe

This section describes how to measure mAs, using the Piranha in the x-ray beam to
trigger the measurement. This means that the measurement starts when the Piranha
detects the radiation.

The MAS-2 probe uses a current clamp probe to measure mAs and mA non-invasively.

The MAS-2 probe is mostly used for mAs
measurements since it is not sensitive enough
to measure tube current on fluoroscopy. The
lowest tube current that can be measured with
MAS-2 is 10 mA. The figure to the left shows
the MAS-2 probe without the cable.
The parameter mAs is available for most type
of measurements but mAs is normally
measured only for X-ray exposures.

To measure tube charge (mAs) with the Piranha MAS-2 Probe

1. Connect the MAS-2 probe to the X-ray generator. Then power on the MAS-2 by

turning the range switch to the 4 A range and make a Reset of the MAS-2 probe by
pressing the yellow knob on the probe.

2. Connect the MAS-2 adapter cable to the Piranha.

3. Set up the Piranha and the handheld computer according to the description in

Setting

Up the Piranha

.

4. In the QABrowser select type of measurement.

5. Next select parameter

mAs

from the menu.

6. The real-time display for mAs is now displayed. Set the generator. Tap

Reset

. Make

an exposure.

12

«
...
143
144
145
146
147
...
»

Содержание Piranha






















































































































































































Отзывы:

Нет отзывов