RTI Piranha Скачать руководство пользователя страница 14

Страница: 14 / 181

2. Description of the Piranha
Indicators and Connectors

Piranha & QABrowser Reference Manual

2014-06/5.5C

The orange indicator

for

Charging of

batteries

is lit when

charging is active.

Note that charging is

possible even when the

power switch is off.

The blue indicator for

Bluetooth

is lit when the

Bluetooth interface is active
and discoverable.

The multi-coloured indicator for

Status

shows the status of the system, e.g.
battery level as described below. Also
works as

Power indicator

, one of the

colours will light when the Piranha is on.

Battery level

The status indicator is used to show the battery level of the Piranha.

1. Starting a system running on batteries the status indicates for 3 seconds:

- Green if battery level over 25 % (4 h left)
- Yellow if battery level between 10 and 25 % (1½-4 h left)
- Red if battery level below 10 % (<1½ h left).

The idea is to get a quick indication when powering on the system if it will take me
through today's work.

2. When running on batteries the status indicator shows:

Status colour

Running time left

Green

>2 hours

Yellow

>1 hours

Red

>15 minutes

Flashing red

<15 minutes

You may also check the battery level in the QABrowser, see section

Power

Status

. For Ocean on the PC, please see the Ocean manual.

See section

Power & Communication Specifications

for more information about

battery charging and discharging times.

External Probe port

and

Opening

for filter position viewing

Here you attach the external probes that come with some models of the Piranha. The

port is marked

EXT

Not all models have this port.

Содержание Piranha






















































































































































































Результаты поиска

Содержание Piranha

Отзывы:

RTI Piranha, Справочное руководство, Страница: 14 / 181

Результаты поиска

Содержание Piranha

Отзывы: