RTI Piranha Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 181

RTI Piranha Скачать руководство пользователя страница 45

3. Description of the QABrowser

Real-time Display and Waveforms

2014-06/5.5C

41

Piranha & QABrowser Reference Manual

mammography. Default values are "DC/HF" and 3.0 mm Al.

8. Make an exposure. Every time the Piranha

recognizes an exposure the RTI logo is
superimposed on screen for a short while.

The Piranha analyses the waveform and shows the
result automatically after the first exposure. If the
result is incorrect the actual waveform type needs to
be set manually, see topic

Settings

for more

information.

The Piranha measures the total filtration for each
exposure (for all measurement types except
mammography). It is shown automatically after the
first exposure.
If you want the QABrowser to lock this value and not
estimate it again for the following exposures, tap

Keep

. You can also enter the total filtration manually

under the settings, see topic

Settings

for more

information.

Up to six values can be shown simultaneously.
Measured kVp, dose, and dose rate values are
compensated depending on actual total filtration
(between 1.5 - 38 mm Al) and waveform type.

The display looks different depending on the type of parameter you selected in step
#3 and if you are using a mAs probe or not. In the pictures below you can see how
the screen looks if you do not measure mAs and if you select just

Tube voltage

.

43

43

«
...
43
44
45
46
47
...
»

Содержание Piranha






















































































































































































Отзывы:

Нет отзывов