RTI Piranha Скачать руководство пользователя страница 149

Страница: 149 / 181

5. Measurements with the Piranha System

Light Measurement

2014-06/5.5C

145

Piranha & QABrowser Reference Manual

5.9.2

Illuminance - Ambient Light (lx)

Read the Piranha Light Probe User's Manual to get information about how to do
different type of measurements and how to use the different adapters.

To measure illuminance (lx):

1. Attach the lux adapter to the Piranha Light Probe as described in the Piranha Light

Probe User's Manual.

2. Connect the Piranha Light Probe to the Piranha.

3. Set up the Piranha and the handheld computer according to the description in

Setting

Up the Piranha

4. In the QABrowser select

Ambient light

from the Type of Measurement menu.

5. Next select parameter

Illuminance

from the menu.

6. The Select Detector screen is now displayed. Select the Piranha Light Probe-L probe.

7. Tap

Select

8. The real-time display for illuminance is now displayed. Cover the white light-sensitive

area of the Piranha Light Probe to shield off all light (you may use the rubber part that
comes with the Piranha Light Probe-M if available). It is very important that you shield
off all light. Then tap

Reset

. After that you can remove the shield and place the light

detector where you want to measure.

9. Read the value on the real-time display.

The figure to the left shows the result. You
can now move the Piranha Light Probe-L
to other points and measure the ambient
light.

If you are measuring very low light intensities it may occur that the Piranha does not
"start" to measure. You should then do as follows:

1. Do as described in step 1 to 8 above.

2. If the Piranha does not start to measure, lift the Piranha Light Probe-L and direct it

towards a bright spot.

3. Place the Piranha Light Probe detector on the spot where you want to measure.

Содержание Piranha






















































































































































































Результаты поиска

Содержание Piranha

Отзывы:

RTI Piranha, Справочное руководство, Страница: 149 / 181

Результаты поиска

Содержание Piranha

Отзывы: