RTI Piranha Скачать руководство пользователя страница 7

Страница: 7 / 181

Piranha & QABrowser Reference Manual

2014-06/5.5C

Contents

.............................................................................................................113

5.5.1

General

.............................................................................................................114

5.5.2

Setting Up the Piranha for Mammography

.............................................................................................................115

5.5.3

kVp, Time, and Dose Measurements with the Internal detector

.............................................................................................................117

5.5.4

Dose Measurements with the Piranha Dose Probe

.............................................................................................................118

5.5.5

HVL Application

.............................................................................................................119

5.5.6

Quick-HVL

.............................................................................................................119

5.5.7

Mammo Compensations and Corrections

..........................................................................................................120

5.5.7.1

Corrections for the Compression Paddle

..........................................................................................................120

5.5.7.2

Normalization

..........................................................................................................122

5.5.7.3

Beam Correction Factor

..........................................................................................................122

5.5.7.4

Corrections for Angular Sensitivity

.............................................................................................................123

5.5.8

Average Glandular Dose, AGD (MGD)

.............................................................................................................124

5.5.9

Mammographic Pre-pulses

.............................................................................................................124

5.5.10

Scanning Beam Mammography

..................................................................................................... 125

5.6

Dental and Panoramic Dental

.............................................................................................................128

5.6.1

kVp, Time, Dose, and Dose Rate

.............................................................................................................130

5.6.2

Waveforms

.............................................................................................................131

5.6.3

Panoramic Systems

.............................................................................................................133

5.6.4

HVL, Total Filtration, and Quick-HVL

..................................................................................................... 134

5.7

.............................................................................................................134

5.7.1

CT kVp

.............................................................................................................136

5.7.2

Parameters for CT Scanner Models

.............................................................................................................137

5.7.3

Quick-HVL and Total Filtration

..................................................................................................... 137

5.8

Tube Current Probes

.............................................................................................................138

5.8.1

MAS-1, Invasive mAs Probe

.............................................................................................................141

5.8.2

MAS-2, Non-invasive mAs Probe

..................................................................................................... 143

5.9

Light Measurement

.............................................................................................................143

5.9.1

Luminance - Monitor/Viewbox (cd/m²)

.............................................................................................................145

5.9.2

Illuminance - Ambient Light (lx)

................................................................................................. 148

Optional Accessories

..................................................................................................... 148

6.1

Holder & HVL Stand

..................................................................................................... 148

6.2

Piranha Panoramic Holder

................................................................................................. 152

Problems and Solutions

..................................................................................................... 152

7.1

Troubleshooting

..................................................................................................... 154

7.2

Bluetooth

.............................................................................................................154

7.2.1

Bluetooth Passkey

.............................................................................................................156

7.2.2

Enable Bluetooth Passkey

..................................................................................................... 156

7.3

How To Report a Problem

................................................................................................. 158

Glossary

..................................................................................................... 169

Index

Содержание Piranha






















































































































































































Результаты поиска

Содержание Piranha

Отзывы:

RTI Piranha, Справочное руководство, Страница: 7 / 181

Результаты поиска

Содержание Piranha

Отзывы: