manualshive.com logo in svg

RTI Piranha, Справочное руководство, Страница: 171 / 181

Поделиться
Скачать
RTI Piranha Скачать руководство пользователя страница 171

8. Glossary

 

2014-06/5.5C

 

167

Piranha & QABrowser Reference Manual

housing to control the "ON" or "OFF" condition of the useful beam.

Sievert (Sv)

The special name for the SI unit of dose equivalent. One sievert equals one joule per
kilogram. The previously used unit was the rem. One sievert is equal to 100 rem.

Signal-to-noise ratio

For video cameras, the ratio of input signal to background interference. The greater the
ratio, the clearer the image.

Simulator

Diagnostic energy X-ray equipment used to simulate a therapy treatment plan outside
the treatment room.

Slice

The single body section imaged in a tomography procedure.

Source

See radiation source.

Source-detector distance (SDD)

The distance measured along the central ray from the centre of the front surface of the
source (X-ray focal spot or sealed radioactive source) to the active surface of the
detector.

Source-to-image-distance (SID)

The distance measured along the central ray from the centre of the front of the surface
of the source (X-ray focal spot of sealed radioactive source) to the surface of the image
detector.

Source-surface distance (source-skin distance) (SSD)

The distance measured along the central ray from the centre of the front surface of the
source (X-ray focal spot or sealed radioactive source) to the surface of the irradiated
object or patient.

Spot film

A radiograph taken during a fluoroscopic examination for the purpose of providing a
permanent record of an area of interest of to verify the filling of a void with contrast
media.

Stray radiation

The sum of leakage and scattered radiation.

Survey

See radiation protection survey.

Target

The part of an X-ray tube anode assembly impacted by the electron beam to produce
the useful X-ray beam.

Tenth value layer (TVL)

Thickness of a specified substance which, when introduced into the path of a given
beam of radiation, reduces the kerma rate to one-tenth of its original rate.

Tomography

A special technique to show in detail images of structures lying in a predetermined

Содержание Piranha






















































































































































































Отзывы:

Нет отзывов