Ross LDP-8242 Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 100

Ross LDP-8242 Скачать руководство пользователя страница 96

5–2 • Service Information

LDP-8242 User Manual (Iss. 03)

Troubleshooting Checklist

Routine maintenance to this openGear product is not required. In the event of problems with your
LDP-8242, the following basic troubleshooting checklist may help identify the source of the
problem. If the frame still does not appear to be working properly after checking all possible
causes, please contact your openGear products distributor, or the Technical Support department at
the numbers listed under the “

Contact Us

” section.

1.

Visual

Review

— Performing a quick visual check may reveal many problems, such as

connectors not properly seated or loose cables. Check the card, the frame, and any
associated peripheral equipment for signs of trouble.

2.

Power Check

— Check the power indicator LED on the distribution frame front panel

for the presence of power. If the power LED is not illuminated, verify that the power
cable is connected to a power source and that power is available at the power main.
Confirm that the power supplies are fully seated in their slots. If the power LED is still
not illuminated, replace the power supply with one that is verified to work.

3.

Re-seat the Card in the Frame

— Eject the card and re-insert it into the frame.

4.

Check Control Settings

— Refer to the Installation and User Controls sections of this

manual to verify all user-adjustable component settings

5.

Input Signal Status

— Verify that source equipment is operating correctly and that a

valid signal is being supplied.

6.

Output Signal Path

— Verify that destination equipment is operating correctly and

receiving a valid signal.

7.

Unit Exchange

— Exchanging a suspect unit with a unit that is known to be working

correctly is an efficient method for localizing problems to individual units.

«
...
94
95
96
97
98
...
»

Содержание LDP-8242





































































































Отзывы:

Нет отзывов