Ross LDP-8242 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 100

Ross LDP-8242 Скачать руководство пользователя страница 59

LDP-8242 User Manual (Iss. 03)

Operating Instructions • 3–25

Input Audio Status

AFD Map

sub-tab allows bi-directional re-aspecting from 4x3 frames to

companion 16x9 frames, and allows customizing aspect ratio settings for

the AFD codes (and the corresponding WSS and VI Translation

equivalents) supported by the card.

Separate control groups for 4x3 and 16x9 coded input frames allow custom ARC (as well as pan/tilt) for various coded frames.
By default, each row is set for its companion re-aspected output, along with output AFD code for the companion output (i.e., 4x3

frames get re-aspected to a companion 16x9 re-aspecting and AFD code, and similarly 16x9 frames get re-aspected to a

companion 4x3 re-aspecting and AFD code).

Your card can only mark the output signal with an AFD code, and does not perform any re-aspecting.

Scaling and Pan/Tilt factors effect the

re-aspecting and position offset here

that result in a 4x3 0010 Letterbox

16x9 Top image when these defaults

are applied.

The AFD coding representing the

applied re-aspecting is applied to the

output video.

In this example, default settings provide the scaling and tilt factors to convert a 16x9-coded 0010 frame to its companion

4x3 0010 Letterbox 16x9 Top frame.

«
...
57
58
59
60
61
...
»

Содержание LDP-8242





































































































Отзывы:

Нет отзывов