Ross LDP-8242 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 100

Ross LDP-8242 Скачать руководство пользователя страница 30

2–4 • Installation

LDP-8242 User Manual (Iss. 03)

Installing a Card

This section outlines how to install a LDP-8242 card when the Rear Module is already installed in
a DFR-8321 series frame. If you are installing the LDP-8242 card in a slot with no rear module, a
rear module is required before cabling can be connected. Refer to the section “

Installing a Rear

Module

” on page 2-3 for rear module installation procedure.

Installing the LDP-8242

Use the following procedure to install the LDP-8242 card into a frame slot:

1.

Check the packaging in which the card was shipped for any extra items such as a rear
module label. In some cases, this label is shipped with the card and should be installed
on the rear I/O connector bank corresponding to the slot location of the card.

2.

Determine the slot in which the card is to be installed.

3.

Open the frame front access panel.

4.

While holding the card by the card-edges, align the card such that the plastic ejector tab
is on the bottom.

5.

Align the card with the top and bottom guides of the slot in which the card is being
installed.

6.

Gradually slide the card into the slot. When resistance is noticed, gently continue
pushing the card until its rear printed circuit edge terminals engage fully into the rear
module mating connector.

7.

Verify that the card is fully engaged in rear module mating connector.

8.

Close the frame front access panel.

9.

Connect the input and output cables as outlined in the section “

Cabling for the

LDP-8242

” on page 2-5.

10.

Repeat steps 1 through 9 for other cards.

This completes the procedure for installing a card in a DFR-8321 series frame. Note that some
Rear Modules and labels have several ventilation holes. To allow maximum ventilation, it is
recommended to place the label fully over connectors such that label is flush with rear module
and holes are not obscured.

Caution

— If required, make certain the rear module(s) is installed before installing

the LDP-8242 card into the frame slot. Damage to card and/or rear module can occur
if module installation is attempted with card already installed in the slot.

Notice

— Heat and power distribution requirements within a frame may dictate

specific slot placement of cards. Cards with many heat-producing components should
be arranged to avoid areas of excess heat build-up.

Caution

— If the card resists fully engaging in rear module mating connector, check

for alignment and proper insertion in slot tracks. Damage to card and/or rear module
may occur if improper card insertion is attempted.

Operating Tip

— To remove a card, press down on the ejector tab to unseat the

card from the rear I/O module mating connector. Evenly draw the card from its slot.

«
...
28
29
30
31
32
...
»

Содержание LDP-8242





































































































Отзывы:

Нет отзывов