Ross LDP-8242 Скачать руководство пользователя страница 93

Страница: 93 / 100

LDP-8242 User Manual (Iss. 03)

Specifications • 4–3

Frame

Reference Input

Number of Inputs

Two non-terminating (looping) Frame Reference inputs
with selectable failover

Standards Supported

SMPTE 170M/318M (“black burst”)
SMPTE 274M/296M (“tri-color”)

Return Loss

> 35dB up to 5.75MHz

Serial Ports

Number of Ports

Rx Functions

Closed captioning input, Dolby® metadata input

Tx Functions

Closed captioning output, Dolby® metadata output,
card status logging

Connector Type

Each port is 3-wire independently configurable for
RS-232 or RS-485 protocol using Phoenix Contact™
connectors with removable screw terminal blocks

GPI Ports

Number of Ports

Mapping

User-configurable by invoking acknowledge and release
settings per selected card presets

Response

GPI acknowledge upon falling-edge input triggered by
R < 10k

(or Vin < 2.0V)

GPI release upon rising-edge input triggered by
R > 10k

(or Vin >2.0V)

“G” (GND) terminal at chassis-ground potential;
suitable for use with 3.3V LVCMOS logic

Maximum Recommended Logic
Control Voltage Range

0 to 5 VDC

Connector Type

Each port is opto-isolated with self-sourcing current on
3-wire (IN 1, IN 2, GND) Phoenix Contact™ connector
with removable screw terminal blocks

Other

Internal Tone Generators

8 built-in tone generators, each configurable for 18
discrete sine wave frequencies ranging from 50Hz to
16kHz
Generator source signal level is equivalent to -20dBu

Frame Communications

10/100Mbps Ethernet with Auto-MDIX

Environment

Operating temperature:

32°F – 104°F (0°C – 40°C)

Relative humidity (operating or
storage)

< 95%, non-condensing

Power

Max. Power Consumption

< 20W

Table 4.1 LDP-8242 Technical Specifications

Category

Parameter

Specification

Содержание LDP-8242





































































































Результаты поиска

Содержание LDP-8242

Отзывы:

Ross LDP-8242, Руководство пользователя, Страница: 93 / 100

Результаты поиска

Содержание LDP-8242

Отзывы: