Ross LDP-8242 Скачать руководство пользователя страница 38

Страница: 38 / 100

3–4 • Operating Instructions

LDP-8242 User Manual (Iss. 03)

Status and Selection LEDs on the Card-edge

The front-edge of the LDP-8242 has LED indicators for communication activity. Basic LED
displays and descriptions are provided in

Table 3.1

Table 3.1 LEDs on the LDP-8242

LED

Color

Display and Description

RMT

Blue

When flashing, this LED indicates when the card is receiving
control messages from DashBoard™.

REF

Blue

When lit, this LED indicates when the card is receiving valid
frame sync when set up for reference frame sync.

LOCK

Blue

When lit, this LED indicates when the LDP-8242 is unable to
lock to frame sync, or unable to lock to input standard.

ERR

This LED is not implemented.

INPUT

FORMAT

Blue

Three blue LEDs indicate the input signal format being received
and locked onto by the card as follows:
•

(1080p 29.97/25, 720p)

•

(625i, 525i)

Continuous cycling of the LEDs indicates the card has not locked
onto a particular format (as in the case of no signal input)

MENU

DEPTH

These LEDs are not implemented.

Содержание LDP-8242





































































































Результаты поиска

Содержание LDP-8242

Отзывы:

Ross LDP-8242, Руководство пользователя, Страница: 38 / 100

Результаты поиска

Содержание LDP-8242

Отзывы: