Ross LDP-8242 Скачать руководство пользователя страница 50

Страница: 50 / 100

3–16 • Operating Instructions

LDP-8242 User Manual (Iss. 03)

Closed Captioning

Provides support for closed captioning setup.

Closed Captioning Input Status

Displays incoming Closed Captioning status as follows:

• If closed captioning is present, a message similar to the example

shown left is displayed. Also displayed is the VANC line number of

the incoming closed captioning packet (or SD waveform-based

VANC line number).

• If no closed captioning is present in the video signal,

Not Present

Disabled

is displayed.

Note

: Packet closed captioning status

Captioning Rejected Due

message can appear due to the items described below. The

closed captioning function assesses cdp_identifier, cdp_frame_rate,

ccdata_present, and caption_service_active items contained in the

packet header to make the determinations listed below. Refer to

CEA-708-B for more information.
The closed captioning function does not support PAL closed

captioning standards.

Closed Captioning Output Insertion Control

Turns on or off the Closed Captioning on the output video.

Note

: When set to On, closed captioning is set to standard default

line number. See the section “Ancillary Data Line Number Locations

and Ranges” on page 3-9. SD output is locked to line 21.
The card does not check for conflicts on a given line number. Make

certain selected line is available and carrying no other data.

Closed Captioning HD Output Line

Selects the VANC line number (9 thru 41) for the closed caption data

when the output is HD.

Note

: Although the output line drop-down will allow any choice

within the 9 thru 41 range, the actual range is automatically

clamped (limited to) certain ranges to prevent inadvertent conflict

with active picture area depending on video format. See Ancillary

Data Line Number Locations and Ranges (p. 3-9) for more

information.
The card does not check for conflicts on a given line number. Make

certain the selected line is available and carrying no other data

unless existing metadata is to be intentionally overwritten.

HD packet-based display

SD waveform-based display

Message

Description

Unsupported

Frame Rate

Film rate closed-captioning (either as

pass-through or up/down conversion) is not

supported by the card.

Data Not Present

Packet is marked from closed captioning

source external to the card that no data is

present.

Service Inactive

Packet is marked from closed captioning

source external to the card indicating packet

does not contain active caption service.

No Data ID

Packet from closed captioning source external

to the card is not properly identified with

0x9669 as the first word of the header

(unidentified packet).

Содержание LDP-8242





































































































Результаты поиска

Содержание LDP-8242

Отзывы:

Ross LDP-8242, Руководство пользователя, Страница: 50 / 100

Результаты поиска

Содержание LDP-8242

Отзывы: