Ross LDP-8242 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 100

Ross LDP-8242 Скачать руководство пользователя страница 33

LDP-8242 User Manual (Iss. 03)

Installation • 2–7

GPI Port Connections

Each GPI input (

GPI

1

,

GPI 2

) consists of an opto-isolator in which a forward-biased LED

activates upon an applied resistance

≤

10 k

Ω

. (or when pulled low from an external logic source

at an applied voltage

≤

2.0 VDC). (

Figure 2.4

)

It is preferable to wire connections to Phoenix Contact™ plugs oriented as shown here rather than
assessing connections on rear module connectors. Note that the orientation of rear module
connectors is not necessarily consistent within a rear module, or between different rear modules.
If wiring is first connected to the Phoenix plug oriented as shown here, the electrical orientation
will be correct regardless of rear module connector orientation.

Figure 2.4

GPI Connections

IN 2

G

IN 1

G

GPI 2

GPI 1

Removable Phoenix plug
view oriented with top
(screw terminals) up

Rear module
PCB connector

1 2 G

«
...
31
32
33
34
35
...
»

Содержание LDP-8242





































































































Отзывы:

Нет отзывов