Ross LDP-8242 Скачать руководство пользователя страница 42

Страница: 42 / 100

3–8 • Operating Instructions

LDP-8242 User Manual (Iss. 03)

Checking Card Information

The operating status and software version the LDP-8242 card can be checked using
DashBoard™.

Figure 3.5

shows and describes the LDP-8242 card information screen using

DashBoard™.

Proper operating status in DashBoard™ is denoted by green icons for the status indicators shown
in

Figure 3.5

. Yellow or red icons respectively indicate an alert or failure condition. Refer to the

section “

Troubleshooting

” on page 3-51 for corrective action.

Figure 3.5

Card Info Utility

The

Tree View

shows the cards seen by DashBoard™.

In this example, Frame 1A is hosting a LDP-8242 card in
slot 7.

Status Displays

Clicking the

Status

sub-tab shows the status the signal

being received by the LDP-8242, and other card
conditions. Green Settings icon shows that any changes
made on DashBoard™ are sucessfully saved on the
card’s memory.
Clicking the

Product

sub-tab shows product information

such as card model, options installed, and firmware
versions. Use this information when communicating to
Ross Video regarding the card.

Содержание LDP-8242





































































































Результаты поиска

Содержание LDP-8242

Отзывы:

Ross LDP-8242, Руководство пользователя, Страница: 42 / 100

Результаты поиска

Содержание LDP-8242

Отзывы: