Ross LDP-8242 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 100

Ross LDP-8242 Скачать руководство пользователя страница 32

2–6 • Installation

LDP-8242 User Manual (Iss. 03)

COMM Port Connections

Connect external interfaces to either the

COMM

1

(Serial A) and/or

COMM 2

(Serial B)

connectors as shown in

Figure 2.3

.

It is preferable to wire connections to Phoenix Contact™ plugs oriented as shown here rather than
assessing polarity on rear module connectors. Note that the orientation of rear module connectors
is not necessarily consistent within a rear module, or between different rear modules. If wiring is
first connected to the Phoenix Contact™ plug oriented as shown here, the electrical orientation
will be correct regardless of rear module connector orientation.

Figure 2.3

COMM Connections for RS-485 and RS-232 Protocols

Note

— RS-485 communication will not work if any of the connections are reversed

from that shown here.

A (-)

B (+)

G

Tx

Rx

G

RS-485

RS-232

Removable Phoenix Contact™
plug view oriented with top
(screw terminals) up

Rear module
PCB connector

2 1 C

«
...
30
31
32
33
34
...
»

Содержание LDP-8242





































































































Отзывы:

Нет отзывов