Ross LDP-8242 Скачать руководство пользователя страница 40

Страница: 40 / 100

3–6 • Operating Instructions

LDP-8242 User Manual (Iss. 03)

Accessing the Card via DashBoard™

Access the LDP-8242 card using DashBoard™ as described below.

Accessing the Card via DashBoard

On the computer connected to the frame LAN, open DashBoard™.

As shown below, in the left side Basic View Tree, locate the frame containing the
LDP-8242 card to be accessed (in this example, Frame 1A).

Basic Tree View — Selecting the Frame

As shown below, expand the tree to access the cards within the frame. Select the card to
be accessed (in this example, Slot 7: LDP-8242).

Basic Tree View — Selecting the LDP-8242

As shown on

Figure 3.4

, when the card is accessed in DashBoard™ its function

submenu screen showing tabs for each function is displayed. (The particular submenu
screen displayed is the previously displayed screen from the last time the card was
accessed by DashBoard™).

Содержание LDP-8242





































































































Результаты поиска

Содержание LDP-8242

Отзывы:

Ross LDP-8242, Руководство пользователя, Страница: 40 / 100

Результаты поиска

Содержание LDP-8242

Отзывы: