Ross LDP-8242 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 100

Ross LDP-8242 Скачать руководство пользователя страница 24

1–16 • Introduction

LDP-8242 User Manual (Iss. 03)

User Control Interface

Figure 1.9

shows the user control interface options for the LDP-8242.

Figure 1.9

User Control Interface

DashBoard™ User Interface

Using DashBoard™, the LDP-8242 and other cards installed in the DFR-8321 series frame can
be controlled from a computer and monitor.

DashBoard™ allows users to view all frames on a network with control and monitoring for all
populated slots inside a frame. This simplifies the setup and use of numerous modules in a large
installation and offers the ability to centralize monitoring. Cards define their controllable
parameters to DashBoard™, so the control interface is always up to date.

The DashBoard™ software can be downloaded from the Ross Video website. The DashBoard™
user interface is described in the section “

Function Submenu List and Descriptions

” on

page 3-10.

If network remote control is to be used for the frame and the frame has not yet been set up for
remote control, refer to the

DFR-8300 Series User Manual

and the

MFC-8300 Series User

Manual

for setup details.

«
...
22
23
24
25
26
...
»

Содержание LDP-8242





































































































Отзывы:

Нет отзывов