manualshive.com logo in svg

Ross LDP-8242, Руководство пользователя, Страница: 12 / 100

Поделиться
Скачать
Ross LDP-8242 Скачать руководство пользователя страница 12

1–4 • Introduction

LDP-8242 User Manual (Iss. 03)

Supported Audio and Video Formats

Table 1.4

 provides details regarding the audio and video formats supported by the LDP-8242.

Table 1.4  Supported Audio and Video Formats

Item

Description/Specification

Input / Output 

Video

Raster Structure:

Frame Rate:

1080i

a

a.

All rates displayed as frame rates; interlaced (“i”) field rates are two times the rate 
value shown.

25; 29.97

720p

50; 59.94

486i

a

29.97

575i

a

25

Embedded 

Audio

The LDP-8242 supports all four groups (16 channels) of embedded audio 
at full 24-bit resolution in both SD (with extended data packets) and HD. 

Discrete AES 

Audio

The AES-8242 licensed option enables the LDP-8242 to accept 16 
channels (8 pairs) of discrete AES audio on 75W BNC connections 
(maximum total of inputs and outputs). Sample rate conversion can be 
employed to accommodate sample rate differences in the AES stream and 
the input video stream.

Содержание LDP-8242





































































































Отзывы:

Нет отзывов