Ross LDP-8242 Скачать руководство пользователя страница 66

Страница: 66 / 100

3–32 • Operating Instructions

LDP-8242 User Manual (Iss. 03)

(continued)

Center Mix Ratio Control

Adjusts the attenuation ratio of center-channel content from 5-channel

source that is re-applied as Lt and Rt content to the DM-L and DM-R

stereo mix.

• Minimum attenuation setting (-0.0 dB) applies no ratiometric

reduction. Center channel content is restored as in-phase

center-channel content with no attenuation, making center-channel

content more predominate in the overall mix.

• Maximum attenuation setting (-80.0 dB) applies a -80 dB ratiometric

reduction of center-channel content. Center-channel content is

restored as in-phase center-channel content at a -80 dB ratio

relative to overall level, making center-channel content less

predominate in the overall mix.
(20.0dB to -80.0 dB range in 0.1 dB steps; default = 0 dB)

Note

: Default setting is recommended to maintain center-channel

predominance in downmix representative to that of the original source

5-channel mix.

Surround Mix Ratio Control

Adjusts the attenuation ratio of surround-channel content from 5-channel

source that is re-applied as Lo and Ro content to the DM-L and DM-R

stereo mix.

• Minimum attenuation setting (-0.0 dB) applies no ratiometric

reduction. Surround-channel content is restored with no

attenuation, making Lo and Ro content more predominate in the

overall mix.

• Maximum attenuation setting (-80.0 dB) applies a -80 dB ratiometric

reduction of surround-channel content. Surround-channel content is

restored at a -80 dB ratio relative to overall level, making

surround-channel content less predominate in the overall mix.
(20.0 dB to -80.0 dB range in 0.1 dB steps; default = 0 dB)

Note

: Default setting is recommended to maintain surround-channel

predominance in downmix representative to that of the original source

5-channel mix.

Содержание LDP-8242





































































































Результаты поиска

Содержание LDP-8242

Отзывы:

Ross LDP-8242, Руководство пользователя, Страница: 66 / 100

Результаты поиска

Содержание LDP-8242

Отзывы: