Ross LDP-8242 Скачать руководство пользователя страница 48

Страница: 48 / 100

3–14 • Operating Instructions

LDP-8242 User Manual (Iss. 03)

(continued)

Offset Controls

Allows the current timecode count to be advanced or delayed on the

output video.

•

Offset Advance

Delay

selects offset advance or delay.

•

Offset Field

delays or advances or delays timecode by one field.

•

Offset Frame

delays or advances or delays timecode by up to 5

frames.

Note

: Default settings are null, with both controls set at zero as shown.

Note

: Although the output line drop-down on the controls described below will allow a particular range of choices, the actual range

is automatically clamped (limited) to certain ranges to prevent inadvertent conflict with active picture area depending on video

format. See Ancillary Data Line Number Locations and Ranges (p. 3-9) for more information.
The card does not check for conflicts on a given line number. Make certain the selected line is available and carrying no other data.

SD VITC Waveform Insertion Controls

For SD output, enables or disables SD VITC waveform timecode insertion

into the output video, and selects the VITC1 and VITC2 line numbers (6

thru 22) where the VITC waveform is inserted.

Note

: If only one output line is to be used, set both controls for the

same line number.

SD VITC Waveform Insertion

control only affects VITC waveforms

inserted (or copied to a new line number) by this function. An

existing VITC waveform on an unscaled SD SDI stream is not

affected by this control and is passed on an SDI output.

SD ATC Insertion Control

For SD output, enables or disables SD ATC_VITC timecode insertion into

the output video, and selects the line number for ATC_VITC.

HD ATC_LTC Insertion Control

For HD output, enables or disables ATC_LTC timecode insertion into the

output video, and selects the line number for ATC_LTC timecode data.

HD ATC_VITC Insertion Control

For HD output, enables or disables ATC_VITC timecode insertion into the

output video, and selects the line number for ATC_VITC1 and

ATC_VITC2.

Note

: If only one output line is to be used, set both controls for the same

line number.

Содержание LDP-8242





































































































Результаты поиска

Содержание LDP-8242

Отзывы:

Ross LDP-8242, Руководство пользователя, Страница: 48 / 100

Результаты поиска

Содержание LDP-8242

Отзывы: