manualshive.com logo in svg

Ross LDP-8242, Руководство пользователя, Страница: 15 / 100

Поделиться
Скачать
Ross LDP-8242 Скачать руководство пользователя страница 15

LDP-8242 User Manual (Iss. 03)

Introduction • 1–7

Video Subsystem Overview

Descriptions below include some functions and features that are available only as options.

The LDP-8242 features a frame sync that can select from either of two card frame reference 
sources, or free-run input video sync. In the event of input video loss of signal, the output can be 
set to disable video, go to black, go to an internal test signal generator pattern, or freeze to the last 
intact frame (last frame having valid SAV and EAV codes).

Video Processor

The LDP-8242 provides full color processing control (luma gain and lift, chroma saturation, and 
color phase) of the output video. The color correction function can be user-selected to be applied 
to input video or output video as shown in 

Figure 1.3

.

Frame Sync Function

This function provides for frame sync control using either one of two external 

FRAME REF IN 

(1,2) 

reference signals distributed with the DFR-8321 series frame, or the input video as a frame 

sync reference. 

This function also allows horizontal and/or vertical offset to be added between the output video 
and the frame sync reference. 

An internal test signal generator provides a selection of 10 standard patterns such as color bars, 
sweep patterns, and other technical patterns. The generator output can be invoked upon loss of 
program video input, or applied to the program video output via user controls.

Timecode Processor

This function uses extracted timecode data from the input video (waveform or ATC), reference 
VITC waveform, or internal (free run) and in turn re-inserts selected timecode data into the 
program video signal.(

Figure 1.2

) The function can monitor video input and reference input for 

supported timecode formats, and then select and prioritize among SDI VITC waveform, SDI 
ATC_VITC, and SDI ATC_LTC timecode sources. If the preferred format is detected, the 
preferred format is used by the card; if the preferred format is not detected, the card uses other 
formats (where available) as desired.

The function also provides conversion between various timecode formats and provides 
independent insertion and line number controls for each SDI timecode output format.

Содержание LDP-8242





































































































Отзывы:

Нет отзывов