Ross LDP-8242 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 100

Ross LDP-8242 Скачать руководство пользователя страница 86

3–52 • Operating Instructions

LDP-8242 User Manual (Iss. 03)

Table 3.3 Status/Error Indicators and Display

Item

Function

Display

Displays 4-digit abbreviated code showing menu and submenu selections. When in a menu
displaying a parameter setting, the display shows parametric scalar value (and +/- sign where
applicable).

Card-edge

Manual

Controls

These controls are not implemented.

Input Format

Indicators

Three blue LEDs indicate the input signal format being received and locked onto by the LDP-8242:
• HD (1080p2997/25, 720p)
• SD (625i, 525i)
Continuous cycling of the LEDs indicates the LDP-8242 has not locked onto a particular format (as
in the case of no signal input).

Menu Depth

Indicators

This function is currently reserved.

RMT LED

When flashing, this LED indicates that the LDP-8242 is receiving control message from remote
network control (DashBoard™)

REF LED

When lit, this LED indicates that the LDP-8242 is receiving valid framesync when set up for
framesync reference.

LOCK LED

When lit, this LED indicates that the LDP-8242 unable to lock to framesync, or unable to lock to
input standard.

ERR LED

This LED is not implemented.

«
...
84
85
86
87
88
...
»

Содержание LDP-8242





































































































Отзывы:

Нет отзывов