Ross LDP-8242 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 100

Ross LDP-8242 Скачать руководство пользователя страница 85

LDP-8242 User Manual (Iss. 03)

Operating Instructions • 3–51

Troubleshooting

This section provides general troubleshooting information and specific symptom/corrective
action for the LDP-8242 card and its remote control interface. The LDP-8242 card requires no
periodic maintenance in its normal operation; if any error indication (as described in this section)
occurs, use this section to correct the condition.

Error and Failure Indicator Overview

The LDP-8242 card itself and its remote control systems all (to varying degrees) provide error
and failure indications. Depending on how the LDP-8242 card is being used (i.e, standalone or
network controlled through DashBoard™), check all available indications in the event of an error
or failure condition.

The various LDP-8242 card and remote control error and failure indicators are individually
described below.

The descriptions below provide general information for the various status and error indicators.
For specific failures, also use the appropriate subsection listed below.

• “

Basic Troubleshooting Checks

” on page 3-55

• “

Processing Error Troubleshooting

” on page 3-55

Card-edge Status/Error Indicators and Display

Figure 3.9

shows and describes the LDP-8242 card-edge status indicators and display. These

indicators and the display show status and error conditions relating to the card itself and remote
(network) communications (where applicable). Because these indicators are part of the card itself
and require no external interface, the indicators are particularly useful in the event of
communications problems with external devices such as network remote control devices.

Figure 3.9

Card-edge Status Indicators and Display

«
...
83
84
85
86
87
...
»

Содержание LDP-8242





































































































Отзывы:

Нет отзывов