manualshive.com logo in svg

Renesas SH7705, Руководство по оборудованию

Renesas SH7705 - мощный процессор с интегрированным аппаратным обеспечением для улучшенной производительности. Скачайте бесплатное руководство по аппаратному обеспечению с manualshive.com, чтобы получить подробную информацию о функциях и настройках устройства. Улучшите работу вашего продукта с помощью данного руководства.

Поделиться
Скачать
background image

Rev. 2.00, 09/03, page 300 of 690

11.5

Software Standby Mode

11.5.1

Transition to Software Standby Mode

The LSI switches from a program execution state to software standby mode by executing the
SLEEP instruction when the STBY bit is 1 in STBCR. In software standby mode, not only the
CPU but also the clock and on-chip peripheral modules halt. The clock output from the CKIO pin
also halts.

The contents of the CPU and cache registers remain unchanged. Some registers of on-chip
peripheral modules are, however, initialized. For more details on the states of on-chip peripheral
modules registers in software standby mode, refer to section 24.3, Register States in Each
Operating Mode.

The procedure for moving to software standby mode is as follows:

1. Clear the TME bit in the WDT’s timer control register (WTCSR) to 0 to stop the WDT.

2. Clear the WDT’s timer counter (WTCNT) to 0 and set the CKS2 to CKS0 bits in WTCSR to

appropriate values to secure the specified oscillation settling time.

3. After the STBY bit in STBCR is set to 1, a SLEEP instruction is executed.

4. Software standby mode is entered and the clocks within the LSI are halted. The STATUS1 pin

output goes low and the STATUS0 pin output goes high.

11.5.2

Canceling Software Standby Mode

Software standby mode is canceled by an interrupt (NMI, IRQ, IRL, PINT, or RTC) or a reset.

Canceling with an Interrupt: The on-chip WDT can be used for hot starts. When the chip detects
an NMI, IRQ*

1

, IRL*

1

, PINT*

1

, or RTC*

1

interrupt, the clock will be supplied to the entire chip

and software standby mode canceled after the time set in the WDT’s timer control/status register
has elapsed. The STATUS1 and STATUS0 pins both go low. Interrupt exception handling then
begins and a code indicating the interrupt source is set in INTEVT and INTEVT2. After branching
to the interrupt handling routine occurs, clear the STBY bit in STBCR. WTCNT stops
automatically. If the STBY bit is not cleared, WTCNT continues operation and transits to software
standby mode*

2

when it reaches H'80. This function prevents data from being broken in case of a

voltage rise when the power supply is unstable. At this time, a manual reset is not accepted until
the STBY bit is cleared to 0.

Interrupts are accepted in software standby mode even when the BL bit in SR is 1. If necessary,
save SPC and SSR to the stack before executing the SLEEP instruction.

Immediately after an interrupt is detected, the phase of the clock output of the CKIO pin may be
unstable, until software standby mode is cancelled.

Содержание SH7705




































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7705

Cabletron Systems Netlink FRX8000 Installation And Setup Manual preview
Netlink FRX8000
Бренд: Cabletron Systems Страницы: 94
Cabletron Systems MMAC-Plus 9E423-24 Reference Manual preview
MMAC-Plus 9E423-24
Бренд: Cabletron Systems Страницы: 10
Cabletron Systems MMAC-Plus 9A128-01 Management Manual preview
MMAC-Plus 9A128-01
Бренд: Cabletron Systems Страницы: 22
Cabletron Systems Spectrum EMM-E6 Addendum Manual preview
Spectrum EMM-E6
Бренд: Cabletron Systems Страницы: 2
Cabletron Systems DLM6C-AA Overview And Setup Manual preview
DLM6C-AA
Бренд: Cabletron Systems Страницы: 54
Cabletron Systems Cabletron BRIM-F6 User Manual preview
Cabletron BRIM-F6
Бренд: Cabletron Systems Страницы: 43
Cabletron Systems Netlink FRX4000 Maintenance Manual preview
Netlink FRX4000
Бренд: Cabletron Systems Страницы: 60
Cabletron Systems 9E132-15 Appendix preview
9E132-15
Бренд: Cabletron Systems Страницы: 8
Cabletron Systems TRXI-22 Addendum preview
TRXI-22
Бренд: Cabletron Systems Страницы: 4
Vonets MINI300 Quick Setting Manual preview
MINI300
Бренд: Vonets Страницы: 8
SMART MOD IIC Installation And Service Manual preview
MOD IIC
Бренд: SMART Страницы: 15
Dialogic EDP-10 Quick Install Manual preview
EDP-10
Бренд: Dialogic Страницы: 2
red lion Yaskawa 2000 Information Sheet preview
Yaskawa 2000
Бренд: red lion Страницы: 5
WAGO 750-459 Manual preview
750-459
Бренд: WAGO Страницы: 48
ZKTeco HVR0402 User Manual preview
HVR0402
Бренд: ZKTeco Страницы: 68
Idis DR-1500 Series Quick Manual preview
DR-1500 Series
Бренд: Idis Страницы: 17
IBM EtherLink XL User Manual preview
EtherLink XL
Бренд: IBM Страницы: 72
Active Communications ACS express Quick Start Manual preview
ACS express
Бренд: Active Communications Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды