manualshive.com logo in svg

Renesas SH7705, Руководство по оборудованию

Renesas SH7705 - мощный процессор с интегрированным аппаратным обеспечением для улучшенной производительности. Скачайте бесплатное руководство по аппаратному обеспечению с manualshive.com, чтобы получить подробную информацию о функциях и настройках устройства. Улучшите работу вашего продукта с помощью данного руководства.

Поделиться
Скачать
background image

Rev. 2.00, 09/03, page 423 of 690

No

Yes

No

Wait

Yes

[1]  Set the receive trigger number
 in 

SCFCR. 

[2]  Reset the receive FIFO. 

[3]  Wait for one bit interval. 

[4]  Reception is started when the RE
 

bit in SCSCR is set to 1. 

[5]  Read receive data while the RDF
 

bit is 1. 

[6]  After the end of reception, clear the
 

RE bit to 0.

Start of reception

Set receive trigger number in RTRG1

and RTRG0 in SCFCR

Set RFRST bit in SCFCR to 1

Clear RFRST bit in SCFCR to 0

1-bit interval elapsed?

Set RE bit in SCSCR

When using receive FIFO data interrupt,

set RIE bit to 1

RDF =1?

Read receive trigger number of receive

data bytes from SCFRDR

Clear RE bit in SCSCR to 0

End of reception

[1]

[2]

[3]

[4]

[5]

[6]

Figure 16.15 Sample Serial Reception Flowchart (2)

(Second and Subsequent Reception)

Содержание SH7705




































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7705

Lauterbach C2000 Manual preview
C2000
Бренд: Lauterbach Страницы: 61
Delta M125HV-113 Quick Installation Manual preview
M125HV-113
Бренд: Delta Страницы: 2
EKF Electronik CompactPCI CC8-BLUES User Manual preview
CompactPCI CC8-BLUES
Бренд: EKF Electronik Страницы: 52
ZALMAN ZM-MFC1 Combo User Manual preview
ZM-MFC1 Combo
Бренд: ZALMAN Страницы: 7
FabiaTech Low Power Series User Manual preview
Low Power Series
Бренд: FabiaTech Страницы: 77
Sans Digital ELITENAS EN104L+(B) Quick Installation Manual preview
ELITENAS EN104L+(B)
Бренд: Sans Digital Страницы: 9
Alcatel-Lucent 9364 Installation And Commissioning Manual preview
9364
Бренд: Alcatel-Lucent Страницы: 60
M-system M5XSBS Instruction Manual preview
M5XSBS
Бренд: M-system Страницы: 4
Kontron MSP8040 Series User Manual preview
MSP8040 Series
Бренд: Kontron Страницы: 32
7th Sense Pixel Processing Juggler User Manual preview
Pixel Processing Juggler
Бренд: 7th Sense Страницы: 148
Lanpro LP-F22 Series Assembling Instructions preview
LP-F22 Series
Бренд: Lanpro Страницы: 3
Lefroy Brooks M1-5100 Installation, Operating, & Maintenance Instructions preview
M1-5100
Бренд: Lefroy Brooks Страницы: 10
SIIG ExpressCard 11-in-1 Reader/Writer Quick Installation Manual preview
ExpressCard 11-in-1 Reader/Writer
Бренд: SIIG Страницы: 8
FOLSOM Blend PRO BP-2002 Installation And Operator'S Manual preview
Blend PRO BP-2002
Бренд: FOLSOM Страницы: 89
SilverStone argon series User Manual preview
argon series
Бренд: SilverStone Страницы: 16
ekwb 3831109810316 User Manual preview
3831109810316
Бренд: ekwb Страницы: 16
Idis DR-8416 Quick Manual preview
DR-8416
Бренд: Idis Страницы: 40
Forcepoint V10000 G4R2 Quick Start Manual preview
V10000 G4R2
Бренд: Forcepoint Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды