Renesas SH7705 Скачать руководство пользователя страница 462 | Manualshive

Страница: 462 / 739

background image

Rev. 2.00, 09/03, page 416 of 690

16.4.5

Serial Operation in Clock Synchronous Mode

Don't care

Don't care

*

*

LSB

MSB

Note:

*

High except in continuous transmission/reception

Serial data

Serial clock

Bit 0

Bit 1

Bit 2

Bit 3

Bit 4

Bit 5

Bit 6

Bit 7

One unit of transfer data (character or frame)

Figure 16.12 Data Format in Clock Synchronous Communication

In clock synchronous serial communication, data on the communication line is output from a
falling edge of the serial clock to the next falling edge. Data is guaranteed valid at the rising edge
of the serial clock.

In serial communication, each character is output starting with the LSB and ending with the MSB.
After the MSB is output, the communication line remains in the state of the MSB.

In clock synchronous mode, the SCIF receives data in synchronization with the rising edge of the
serial clock.

1. Data Transfer Format

A fixed 8-bit data format is used. No parity or multiprocessor bits are added.

2. Clock

An internal clock generated by the on-chip baud rate generator or an external clock input through
the SCK pin can be selected as the serial clock for the SCIF, according to the setting of the CKE1
and CKE0 bits in SCSCR.

Eight serial clock pulses are output in the transfer of one character, and when no
transmission/reception is performed, the clock is fixed high. However, when the operation mode is
reception only, the synchronous clock output continues while the RE bit is set to 1. To fix the
clock high every time one character is transferred, write to the transmit FIFO data register
(SCFTDR) the same number of dummy data bytes as the data bytes to be received and set the TE
and RE bits to 1 at the same time to transmit the dummy data. When the specified number of data
bytes are transmitted, the clock is fixed high.

3. Data Transfer Operations

a. SCIF Initialization:

Before transmitting and receiving data, it is necessary to clear the TE and RE bits in SCSCR to 0,
then initialize the SCIF as described below.

«
...
460
461
462
463
464
...
»

Содержание SH7705




































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7705

Бренд: Campbell Страницы: 38

Power Control Processor

Бренд: ETC Страницы: 64

Core 2 Quad Q9400

Бренд: Intel Страницы: 2

Wisenet PRN-6400B4

Бренд: Hanwha Techwin Страницы: 14

Бренд: ZALMAN Страницы: 9

Бренд: AOpen Страницы: 18

2000 IDU Series

Бренд: EMS Страницы: 52

Бренд: Xtreme Страницы: 83

Бренд: Vacron Страницы: 16

Acme Packet 3900

Бренд: Oracle Страницы: 70

Modular Fast Fiber Switch Converter MT-RJ

Бренд: Lindy Страницы: 3

Бренд: ELSA Страницы: 60

Бренд: Helmholz Страницы: 14

EZ-KIT LITE ADSP-2191

Бренд: Analog Devices Страницы: 98

Бренд: H3C Страницы: 62

Бренд: SilverStone Страницы: 17

Бренд: Ublox Страницы: 11

DMX-Relais 2 INRUSH

Бренд: DMX4ALL Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды