manualshive.com logo in svg

Renesas SH7705, Руководство по оборудованию

Renesas SH7705 - мощный процессор с интегрированным аппаратным обеспечением для улучшенной производительности. Скачайте бесплатное руководство по аппаратному обеспечению с manualshive.com, чтобы получить подробную информацию о функциях и настройках устройства. Улучшите работу вашего продукта с помощью данного руководства.

Поделиться
Скачать
background image

Rev. 2.00, 09/03, page xxxi of xlvi

23.2

Input/Output Pins......................................................................................................... 568

23.3

Register Descriptions ................................................................................................... 569
23.3.1 Bypass Register (SDBPR)................................................................................ 569
23.3.2 Instruction Register (SDIR) ............................................................................. 569
23.3.3 Boundary Scan Register (SDBSR) ................................................................... 570
23.3.4 ID Register (SDID).......................................................................................... 577

23.4

Operation..................................................................................................................... 578
23.4.1 TAP Controller................................................................................................ 578
23.4.2 Reset Configuration......................................................................................... 579
23.4.3 TDO Output Timing ........................................................................................ 579
23.4.4 UDI Reset ....................................................................................................... 580
23.4.5 UDI Interrupt .................................................................................................. 580

23.5

Boundary Scan............................................................................................................. 581
23.5.1 Supported Instructions ..................................................................................... 581
23.5.2 Points for Attention ......................................................................................... 582

23.6

Usage Notes................................................................................................................. 583

23.7

Advanced User Debugger (AUD) ................................................................................. 583

Section 24 List of Registers ........................................................................... 585

24.1

Register Addresses
(by functional module, in order of the corresponding section numbers) ......................... 586

24.2

Register Bits ................................................................................................................ 595

24.3

Register States in Each Operating Mode ....................................................................... 614

Section 25 Electrical Characteristics .............................................................. 623

25.1

Absolute Maximum Ratings......................................................................................... 623

25.2

DC Characteristics ....................................................................................................... 625

25.3

AC Characteristics ....................................................................................................... 630
25.3.1 Clock Timing .................................................................................................. 631
25.3.2 Control Signal Timing ..................................................................................... 636
25.3.3 AC Bus Timing ............................................................................................... 638
25.3.4 Basic Timing................................................................................................... 640
25.3.5 Burst ROM Timing ......................................................................................... 645
25.3.6 Synchronous DRAM Timing ........................................................................... 646
25.3.7 DMAC Signal Timing ..................................................................................... 668
25.3.8 TMU Signal Timing ........................................................................................ 669
25.3.9 RTC Signal Timing ......................................................................................... 670
25.3.10 16-Bit Timer Pulse Unit (TPU) Signal Timing ................................................. 670
25.3.11 SCIF Module Signal Timing ............................................................................ 671
25.3.12 USB Module Signal Timing............................................................................. 672
25.3.13 USB Transceiver Timing ................................................................................. 673
25.3.14 Port Input/Output Timing ................................................................................ 674
25.3.15 UDI Related Pin Timing .................................................................................. 675

Содержание SH7705




































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7705

B2 ABB2050 Instruction Manual preview
ABB2050
Бренд: B2 Страницы: 52
Ratoc Systems SmartMedia Adapter PC Card REX-SMA01F Product Manual preview
SmartMedia Adapter PC Card REX-SMA01F
Бренд: Ratoc Systems Страницы: 75
Javad TRIUMPH-3NR User Manual preview
TRIUMPH-3NR
Бренд: Javad Страницы: 35
Maxim MAX1415 Specification Sheet preview
MAX1415
Бренд: Maxim Страницы: 14
Compaq StorageWorks AIT 35GB AutoLoader Overview And Installation preview
StorageWorks AIT 35GB AutoLoader
Бренд: Compaq Страницы: 4
Telit Wireless Solutions HE922-3GR Hardware User'S Manual preview
HE922-3GR
Бренд: Telit Wireless Solutions Страницы: 113
EVOC 6336-STG-YX Manual preview
6336-STG-YX
Бренд: EVOC Страницы: 57
A2B Electronics ECX-200 Installation Manual preview
ECX-200
Бренд: A2B Electronics Страницы: 24
ZALMAN CNPS6000-Al User Manual preview
CNPS6000-Al
Бренд: ZALMAN Страницы: 6
XJTAG XJLink2-CFM User Manual preview
XJLink2-CFM
Бренд: XJTAG Страницы: 9
Xilinx Zynq-7000 Manual preview
Zynq-7000
Бренд: Xilinx Страницы: 8
EMTRUST CP75X User Manual preview
CP75X
Бренд: EMTRUST Страницы: 103
Network Critical SmartNA-X User Manual preview
SmartNA-X
Бренд: Network Critical Страницы: 200
Bose PowerMatch ESPLink Quick Start Manual preview
PowerMatch ESPLink
Бренд: Bose Страницы: 2
EVGA inDtube Instructions preview
inDtube
Бренд: EVGA Страницы: 3
Cooler Master MCY-C3P1-KWNN Manual preview
MCY-C3P1-KWNN
Бренд: Cooler Master Страницы: 4
8e6 Technologies Threat Analysis Reporter TAR Quick Start Manual preview
Threat Analysis Reporter TAR
Бренд: 8e6 Technologies Страницы: 76
INGENIA Everest CORE Product Manual preview
Everest CORE
Бренд: INGENIA Страницы: 58

Бренды по названию

Популярные бренды

Загрузить еще бренды