PRONAR RC2100-2 Скачать руководство пользователя страница 93

Страница: 93 / 121

SECTION 5

Pronar RC2100-2

5.15

Brake repairs, changes of brake linings etc. may be only undertaken in authorised service

points. Making unauthorised repairs and modifications by the user voids the guarantee.

Among the service operations which may be performed by the trailer user there is only brake

adjustment by changing the setting of expander arms.

5.2.9 REPLACEMENT OF PARKING BRAKE CABLE AND ADJUSTMENT OF

CABLE TENSION.

Proper operation of the parking brake is dependent on the effectiveness of the axle brake

and the correct brake cable tension.

FIGURE 5.7

Adjustment of parking brake cable tension

(1) brake crank mechanism, (2) hand brake cable, (3) shackle, (4) u-shaped clamp, (5) clamp

nuts, (6) guide rollers

Replacing the parking brake cable

Hitch trailer to tractor. Park trailer and tractor on level surface.

Place wheel chocks under trailer wheel.

Содержание RC2100-2


























































































































Результаты поиска

Содержание RC2100-2

Отзывы:

Похожие инструкции для RC2100-2

Бренды по названию

Популярные бренды

PRONAR RC2100-2, Руководство оператора

Результаты поиска

Содержание RC2100-2

Отзывы:

Похожие инструкции для RC2100-2

Бренды по названию

Популярные бренды