PRONAR RC2100-2 Скачать руководство пользователя страница 112

Страница: 112 / 121

Pronar RC2100-2

SECTION 5

5.34

Parts to be lubricated with machine oil should be wiped with dry clean cloth and then a small

quantity of oil should be applied to their surfaces (using oil can or brush). Wipe off excess oil.

Change of grease in hub bearings should be entrusted to specialised service points,

equipped with the appropriate tools. According to the recommendations of the axle

Manufacturer, dismantle the entire hub, remove the bearing and individual sealing rings. After

careful washing and inspection, mount lubricated elements. If necessary, bearing and seals

should be replaced with new parts. Lubrication of axle bearings shall be performed at least

once in 2 years or every 50,000 km. In the event of intensive use, lubrication should be

performed more frequently.

Empty grease or oil containers should be disposed of according to the recommendations of

the lubricant Manufacturer.

During trailer operation, the user is obliged to observe lubrication instructions according
to attached lubrication schedule.

5.8

CONSUMABLES

5.8.1 HYDRAULIC OIL

Always adhere to the principle that the oil in the trailer hydraulic system and in the tractor

hydraulic system are of the same type. In the event of application of different types of oil

make certain that both hydraulic substances may be mixed together. Application of different

oil types may cause damage to trailer or tractor. In a new machine, the hydraulic system is

filled with L HL32 Lotos hydraulic oil.

If it is necessary to change hydraulic oil for another oil, check the recommendations of the oil

Manufacturer very carefully. If it is recommended to flush the system with the appropriate

preparation, then comply with these recommendations. Attention should be given, so that

chemical substances used for this purpose do not damage the materials of the hydraulic

system. During normal trailer use change of hydraulic oil is not necessary, but if required, this

operation should be entrusted to a specialist service point.

Содержание RC2100-2


























































































































Результаты поиска

Содержание RC2100-2

Отзывы:

Похожие инструкции для RC2100-2

Бренды по названию

Популярные бренды

PRONAR RC2100-2, Руководство оператора

Результаты поиска

Содержание RC2100-2

Отзывы:

Похожие инструкции для RC2100-2

Бренды по названию

Популярные бренды