PRONAR RC2100-2 Скачать руководство пользователя страница 66

Страница: 66 / 121

Pronar RC2100-2

SECTION 4

4.8

Setting the support to driving position

Immobilise tractor and trailer with parking brake.

The tractor must be connected with the trailer before the support foot

is raised.

Unlock the cotter pin (4) and remove the safety pin from the parking position

(3).

Turn support foot (1) to position (2).

Insert safety pin in position (5) and secure it with cotter pin (4).

Prior to moving off, release trailer's parking brake.

ATTENTION

Do NOT move off or drive with the support in parking position Be sure to change support
to the driving position.

Do NOT travel with the trailer if the support securing elements are damaged or lost –
safety pin (3) and R-clip (4).

Setting the support to rest position

Immobilise tractor and trailer with parking brake.

Unlock the cotter pin (4) and remove the safety pin from the driving position

(5) – figure (4.1).

Turn the support to position (1) – parking position.

Insert safety pin to parking position (3) and secure it with cotter-pin (4).

DANGER

Danger of crushing. Be especially careful when lowering the support – this refers to
bystanders or helpers.

Содержание RC2100-2


























































































































Результаты поиска

Содержание RC2100-2

Отзывы:

Похожие инструкции для RC2100-2

Бренды по названию

Популярные бренды

PRONAR RC2100-2, Руководство оператора

Результаты поиска

Содержание RC2100-2

Отзывы:

Похожие инструкции для RC2100-2

Бренды по названию

Популярные бренды