PRONAR RC2100-2 Скачать руководство пользователя страница 95

Страница: 95 / 121

SECTION 5

Pronar RC2100-2

5.17

ATTENTION

Clamp jaws must be placed on the side of the load bearing cable - see figure

(5.8).

Adjustment of parking brake cable tension

Checking and/or adjustment of parking brake:

•

every 12 months,

•

if needed.

Hitch trailer to tractor. Park trailer and tractor on level surface.

Place wheel chocks under trailer wheel.

Unscrew the brake mechanism bolt maximally (1) – figure (5.7),

(counterclockwise).

Loosen nuts of handbrake cable clamps located near expander lever

Tighten cable and tighten clamps.

Length of parking brake cable should be so selected that at total

release of working and parking brake the cable would be loose and

hanging by 1 - 2 cm compared to fully tensioned cables.

Adjustment of parking brake cable tension should be conducted in the event of:

stretching of cable,

loosening of parking brake cable clamps

after adjustment of axle brakes,

after repairs of axle brake system,

after repairs of parking brake system.

Before the adjustment, make certain that the axle brake is correctly adjusted and is

functioning properly.

Содержание RC2100-2


























































































































Результаты поиска

Содержание RC2100-2

Отзывы:

Похожие инструкции для RC2100-2

Бренды по названию

Популярные бренды

PRONAR RC2100-2, Руководство оператора

Результаты поиска

Содержание RC2100-2

Отзывы:

Похожие инструкции для RC2100-2

Бренды по названию

Популярные бренды