PRONAR RC2100-2 Скачать руководство пользователя страница 65

Страница: 65 / 121

SECTION 4

Pronar RC2100-2

4.7

DANGER

Exercise caution when unhitching the trailer from the tractor. Ensure good visibility.
Unless it is necessary, do not go between tractor and trailer.

Before disconnecting conduits and drawbar eye, close tractor cab and secure it against
access by unauthorised persons.

4.3

SUPPORT LEG OPERATION

DANGER

While placing the support in driving position, exercise caution and do not place fingers
between the support mounting socket and the support. Danger of severing or crushing.

FIGURE 4.1

Support operation

(1) support in parking position, (2) support in driving position, (3) safety pin in parking

position, (4) cotter pin, (5) safety pin in driving position

Содержание RC2100-2


























































































































Результаты поиска

Содержание RC2100-2

Отзывы:

Похожие инструкции для RC2100-2

Бренды по названию

Популярные бренды

PRONAR RC2100-2, Руководство оператора

Результаты поиска

Содержание RC2100-2

Отзывы:

Похожие инструкции для RC2100-2

Бренды по названию

Популярные бренды