background image

SECTION 1 

PRONAR RC2100-2 

1.13 

Detailed information concerning hydraulic oil may be found on the product's Material Safety 

Data Sheet. 

 

TIP 

 

The hydraulic system of the trailer is filled with L-HL32 Lotos hydraulic oil. 

 

ATTENTION 

 

Waste oil should only be taken to the appropriate facility dealing with the re-use of this 
type of waste. Do NOT throw or pour oil into sewerage or water tanks.  

 

1.7

 

WITHDRAWAL FROM USE 

In  the  event  of  decision  by  the  user  to  withdraw  the  trailer  from  use,  comply  with  the 

regulations  in  force  in  the  given  country  concerning  withdrawal  from  use  and  recycling  of 

machines  withdrawn  from  use.  Before  commencing  dismantling,  totally  remove  the  oil  from 

the  hydraulic  system  and  reduce  air  pressure  completely  in  the  pneumatic  braking  system 

(e.g. using air tank drain valve).  

 

DANGER 

 

During  dismantling,  use  the  appropriate  tools,  equipment  (overhead  travelling  crane, 
crane  or  hoist  etc.)  and  use  personal  protection  equipment,  i.e.  protective  clothing, 
footwear, gloves and eye protection etc. 

Avoid contact of skin with oil. Do not allow used hydraulic oil to spill. 

 
Worn out or damaged parts that cannot be reclaimed should be taken to a collection point for 

recyclable raw materials. Hydraulic oil should be taken to the appropriate facility dealing with 

the re-use of this type of waste. 

Содержание RC2100-2


























































































































Отзывы: