PRONAR RC2100-2 Скачать руководство пользователя страница 118

Страница: 118 / 121

Pronar RC2100-2

SECTION 5

5.40

5.12

TROUBLESHOOTING

TABLE 5.9

Troubleshooting

FAULT

CAUSE

REMEDY

Problem with moving off

Applied parking brake

Release parking brake.

Excessive bearing
slackness.

Check slackness and adjust if
needed.

Damaged bearings.

Replace bearings.

Noise in axle hubs

Damaged hub parts.

Replace.

Insufficient pressure in the
system.

Damaged brake valve in tractor.
Repair or replace.

Leaking system conduits or
connections. Check system for
tightness.

Incorrect main or parking
brake adjustment.

Regulate setting of expander
arms.

Poor efficiency of braking
system.

Excessive heating of axle
hubs

Worn brake linings

Change brake shoes.

Improper hydraulic oil
viscosity

Check oil quality, make sure that
the oil in both machines is of the
same type. If necessary change
oil in tractor or in trailer.

Insufficient tractor hydraulic
pump output, damaged
tractor hydraulic pump.

Check tractor hydraulic pump.

Damaged or contaminated
cylinder

Check cylinder piston rod
(bending, corrosion), check
cylinder for tightness (cylinder
piston rod seal), if necessary,
repair or replace the cylinder.

Incorrect hydraulic
system operation

Damaged hydraulic
conduits.

Check and ascertain that hydraulic
conduits are tight, not fractured
and properly tightened. If
necessary, replace or tighten.

Содержание RC2100-2


























































































































Результаты поиска

Содержание RC2100-2

Отзывы:

Похожие инструкции для RC2100-2

Бренды по названию

Популярные бренды

PRONAR RC2100-2, Руководство оператора

Результаты поиска

Содержание RC2100-2

Отзывы:

Похожие инструкции для RC2100-2

Бренды по названию

Популярные бренды