PRONAR RC2100-2 Скачать руководство пользователя страница 86

Страница: 86 / 121

Pronar RC2100-2

SECTION 5

5.8

Secure castellated nut with cotter pin and mount the hub cap.

Delicately tap the hub cap with rubber or wooden mallet.

FIGURE 5.3

Adjustment of wheel axle bearings

(1) hub cover, (2) castellated nut, (3) cotter pin

The wheel should turn smoothly without stiffness or detectable resistance not originating from

abrasion of brake shoes in brake drum. Adjustment of bearing play may only be conducted

when the trailer is hitched to tractor and it is not loaded.

TIP

If the wheels are removed, bearing play is easy to check and adjust.

5.2.6 MOUNTING AND DISMOUNTING WHEELS, INSPECTION OF WHEEL NUT

TIGHTENING.

Wheel removal

Immobilise trailer with parking brake.

Place securing chocks under trailer wheel (opposite of the wheel being

dismounted).

Содержание RC2100-2


























































































































Результаты поиска

Содержание RC2100-2

Отзывы:

Похожие инструкции для RC2100-2

Бренды по названию

Популярные бренды

PRONAR RC2100-2, Руководство оператора

Результаты поиска

Содержание RC2100-2

Отзывы:

Похожие инструкции для RC2100-2

Бренды по названию

Популярные бренды