Parker SciLog FilterTec Plus Скачать руководство пользователя

Страница: 50 / 72

5.5 Setup: Printer

Printer

allows the setting of RS-232 communication parameters needed for connection to a

Parker serial printer or to a PC for data collection.



Print Time:

Controls how fast the FilterTec Plus sends data points in Minutes: Seconds.

Max is 30:00 minutes; Min is 00:05 seconds. Default = 00:10 seconds.



Type:

Allows use of two styles of small serial printers, Seiko, a thermal unit, and Starr, a

dot matrix. For all other printers, and PC communication, Seiko setting is used and is the
default.



Stop Bits:

Select 1 or 2. Default = 1.



Parity:

Select Even, Odd or None. Default = None.



Word Length:

Select 7 or 8 Bits. Default = 8 Bits.



Baud Rate:

Select 300, 600, 1200, 2400, 4800, 9600, or 38.4. Default = 9600



Print Delay:

Used to slow down the output for printers with small buffers. Select 0 – 5

seconds. Default = 0 seconds.

SELECT

- PRINT – PRINT TIME
UP DOWN SELECT

- SETUP - PRINTER
UP DOWN SELECT

PRINT TIME:

00:10

UP DOWN SELECT

- PRINT –

TYPE

UP DOWN SELECT

TYPE:

SEIKO

UP DOWN SELECT

- PRINT – STOP BITS
UP DOWN SELECT

STOP BITS:

UP DOWN SELECT

- PRINT –

PARITY

UP DOWN SELECT

PARITY:

NONE

UP DOWN SELECT

- PRINT – WORD LENGTH
UP DOWN SELECT

WORD LENGTH: 8 BITS
UP DOWN SELECT

- PRINT – BAUD RATE
UP DOWN SELECT

BAUD RATE: 9600
UP DOWN SELECT

DOWN

- PRINT – PRINT DELAY
UP DOWN SELECT

PRINT DELAY:

UP DOWN SELECT

DOWN

Содержание SciLog FilterTec Plus









































































Результаты поиска

Содержание SciLog FilterTec Plus

Отзывы:

Похожие инструкции для SciLog FilterTec Plus

Бренды по названию

Популярные бренды

Parker SciLog FilterTec Plus, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание SciLog FilterTec Plus

Отзывы:

Похожие инструкции для SciLog FilterTec Plus

Бренды по названию

Популярные бренды