Parker SciLog FilterTec Plus Скачать руководство пользователя | Manualshive

Страница: 58 / 72

background image

58

Here the data sheet is setup for the mode being used and the number of pressure sensors in
use.

As this spreadsheet is also used for the FilterTec, options for one, two or three balances exist.
Setting it for less than three will not affect the data received; there may be columns of data that
are hidden.

Most common will be Constant Rate Mode and three Sensors. Choose the mode and either
one or three sensors and click on OK. These choices may be changed between runs if the need
arises by pressing the “Data Sheet Setup” button on the spreadsheet.

After pressing the ok button, the next dialog appears:

Enter the operator’s information and that of the filter and sample being run.

The Membrane area in square meters is a mandantory field, and must be filled in for Flux
calculations to function properly.

A default value of .000962 sq meters is entered for those using 47mm diameter filters. These
fields may be updated for later runs by pressing the “Operator Info” button on the spreadsheet.

«
...
56
57
58
59
60
...
»

Содержание SciLog FilterTec Plus









































































Отзывы:

Нет отзывов

Похожие инструкции для SciLog FilterTec Plus

Бренд: Campden instruments Страницы: 8

Бренд: Rath Страницы: 3

Бренд: NORLUX Страницы: 2

Бренд: Above All Страницы: 4

Бренд: Baker Страницы: 82

Бренд: e+p Elektrik Handels Страницы: 2

Martin ERA 800 Performance

Бренд: Harman Страницы: 32

Martin ERA 600 Performance

Бренд: Harman Страницы: 32

Бренд: Hardt Страницы: 22

Бренд: Sabre Страницы: 2

Бренд: Jasco Страницы: 2

Бренд: Nectar Страницы: 46

Бренд: Neauvia Страницы: 17

RIDA qLine ZG2601

Бренд: R-Biopharm Страницы: 23

ST70 Instrument

Бренд: Raymarine Страницы: 12

Бренд: Raven Страницы: 73

Бренд: Tascam Страницы: 3

Бренд: RAB Lighting Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды