Parker SciLog FilterTec Plus Скачать руководство пользователя | Manualshive

Страница: 55 / 72

background image

55

5.8 Setup: Pump, continued:

Setup: Pump

provides configuration of global settings related to the pump. Generally, the

default values here do not need to be changed. Any changes required for a particular system
will be made at the factory, and would only need to be modified if a “Factory Reset” is
performed.



Keypad Beep:

Determines if the buttons “beep” when pressed. Default = ON.



Factory Reset:

Resets the system to the factory default settings for all menus. Requires

pressing “YES” to both the “Clear All Memory?” and “Are You Sure?” prompts.



ASCII Feedback:

Controls responses sent to a PC upon receipt of a remote command.

Default = ON.



External Run-Stop:

Controls action of the Footswitch connection, which is part of the

External I/O DB37 connector (pins 19 and 37). Choose Pulse for footswitch type control
where the contacts are closed and then opened. Choose Level for contact closure control
where closed = Run and open = Stop. Run key is disabled when this is set to Level except
in Manual Mode. Default = Pulse.



Power-Up:

Controls the action of the system upon power-up. Choose from Menu, Mode, or

Run. Menu = the system returns to the top of the Menu. Mode = the system returns to the
last Mode it was in. Run = the system returns to the last Mode it was in and starts the
process.



Pump Tubing:

If Pump Head is set to Peristaltic, all nine standard tubing sizes can be

chosen. Used with Motor RPM setting to determine proper calibration curve. Default = 16.



Pump Head:

Choose between Peristaltic, RH1, RH0 and RH00. Also used to access the

proper calibration curve. Default = Peristaltic.



Motor RPM:

Choose between 8, 160 and 600 rpm, matching the motor installed in the

system. This will be set at the factory. It will need to be reset after a Factory Reset if other
than the default. Default = 160.



Motor Start:

Controls how fast the motor starts. Hard is fast, Soft is slow. Default = Hard.



TTL 1 On-Off:

Controls action of TTL Switch 1, used for Master/Slave control of another

system or device with TTL input control. Set to Yes, TTL 1 changes states from High to Low
when the system is told to run the motor. Set to No, it does not. Default = Yes.



Switch Polarity:

Controls the polarity of the TTL switches. Inverted = High when not

activated, Low when activated. Normal = Low when not activated, High when activated.
Default = Inverted to allow for proper Master/Slave control.



Switch Configuration:

Sets the action of the TTL switches. Choose between Level and

Pulse. Default = Pulse. Set to Level to allow for proper Master/Slave control.

«
...
53
54
55
56
57
...
»

Содержание SciLog FilterTec Plus









































































Отзывы:

Нет отзывов

Похожие инструкции для SciLog FilterTec Plus

Бренд: Zetec Страницы: 23

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: Qazqa Страницы: 2

Бренд: NCR Страницы: 20

Бренд: DARAY Страницы: 32

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: MacDon Страницы: 74

Бренд: MAGIC FX Страницы: 25

9NP-B7524 Series

Бренд: Nautilus Страницы: 2

Be strong NS 700X

Бренд: Nautilus Страницы: 34

Бренд: Nautilus Страницы: 21

Бренд: Pahlen Страницы: 20

Бренд: Paia Страницы: 7

Бренд: Qiagen Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды