manualshive.com logo in svg

Parker SciLog FilterTec Plus, Инструкция по установке, эксплуатации и обслуживанию

«Parker SciLog FilterTec Plus» - продукт, который необходим для обеспечения чистоты в вашей системе. Перед установкой, эксплуатацией и обслуживанием убедитесь в правильном использовании, скачав руководство по установке, эксплуатации и обслуживанию с manualshive.com. Это руководство доступно для бесплатного скачивания.

Поделиться
Скачать
background image

 

 

15

Part A: FilterTec Plus Hardware 

1.0 Overview: 

The FilterTec Plus is a DEF laboratory-scale filtration system that automates filterability studies 
and dead end filtration processes. In DEF, process solution is pumped through a filtration 
device, typically a 47mm diameter disk filter or something larger, having a user-selected 
porosity. In contrast to older, less efficient DEF procedures, Parker’s new “Pmaintain” Alarm 
method automates direct flow filtration (DFF) of dilute protein solutions while providing a 35-
50%* increase in filter utilization and filtration yield. (*process solution dependant) 

Parker’s new “Pmaintain” Alarm method consists of the following steps: Initially, a user-defined 
constant pump rate is implemented in Constant Rate Mode until a user-defined pressure limit is 
reached. At this point, the fluid handling system automatically switches to a constant pressure 
delivery, i.e. modulating the pump output until a user-defined lower filtration flow limit (collection 
rate) is reached and the pump automatically stops. 

The FilterTec Plus system provides ease of use and operational safety:

 Several user 

definable alarm conditions can be continuously monitored and displayed. 

The user defined alarms include:  

 

High Pressure Alarm

 to monitor filter 

plug-up conditions, the Pmaintain Alarm is 
part of this Alarm menu, will change the 
unit from Constant Rate to Constant 
Pressure at a user-defined limit. 

 

Low Pressure Alarm

 to monitor system 

leakage. 

 

Low Flow Alarm

 to monitor filter plug-up 

conditions. Used along with Pmaintain in 
High Pressure Alarm to terminate the 
filtration process. 

 

Hi Temperature 

to monitor the 

temperature of your solution. 

 

Cumulative Volume Alarm

 to monitor 

total volume based on the feed rate. 

 

Filtrate Weight Alarm

 to quantitatively 

measure the filtrate yield. 

 

Run Time Alarm

 that stops the pump 

action when a user defined filtration time 
has elapsed. 

 

Hi and Low Analog Alarms

 allow you to 

monitor inputs from other devices to 
control your process. (pH, conductivity or 
turbidity sensors, etc.) 

All alarms provide an auditory signal; the pump stops when user defined alarm limits are 
exceeded. Alternatively, any alarm can be selectively disabled. All pump filtration, as well as 
alarm parameters can be printed out at user defined time intervals with a Parker serial printer. 
Alternatively, all of the collected data can be sent to a supervisory computer for data archiving 
using SciDoc or HyperTerminal. 

The Masterflex Easy-Load II peristaltic pump heads can accommodate PharMed and Platinum-
cured Silicone pump tubing, including sizes 13, 14, 16, 25, & 17. If equipped with the lager 
model, sizes 15, 24 & 35 can be accommodated. Feed rates for all pump tube sizes are factory 
calibrated; however, the user can easily recalibrate with a single keystroke from the FilterTec 
Plus front panel. The pump head delivers flow rates ranging from 0.03 ml / min. to 2200 ml / 
min. for each of the two pump channels depending on motor rpm. 

NOTE: 

The FilterTec Plus usually is configured with a 160-rpm motor. However, if your flow rate 

needs require, the FilterTec Plus is available with either a 600-rpm or 8-rpm motor. In Setup: 
Pump: Motor: Rpm, select the RPM of your installed motor. By doing so, the FilterTec Plus will 
select the appropriate factory installed calibration curves and flow rates. 

Содержание SciLog FilterTec Plus









































































Отзывы:

Нет отзывов

Похожие инструкции для SciLog FilterTec Plus

Fender 1 Brochure preview
1
Бренд: Fender Страницы: 15
J D Squared 4 Assembly & Operating Instructions preview
4
Бренд: J D Squared Страницы: 18
B&K 700 Calibration Manual preview
700
Бренд: B&K Страницы: 5
B&K 1621 Instruction Manual preview
1621
Бренд: B&K Страницы: 28
EWM Tetrix 351 AC/DC Smart FW Operating Instructions Manual preview
Tetrix 351 AC/DC Smart FW
Бренд: EWM Страницы: 117
Fisher Scientific Isotemp User Manual preview
Isotemp
Бренд: Fisher Scientific Страницы: 42
Ace AFM-5 Operating Manual preview
AFM-5
Бренд: Ace Страницы: 17
ACE INSTRUMENTS Solid Operating Manual preview
Solid
Бренд: ACE INSTRUMENTS Страницы: 33
ACE INSTRUMENTS ALP-1 med Quick Start Manual preview
ALP-1 med
Бренд: ACE INSTRUMENTS Страницы: 2
ACE INSTRUMENTS ACE Easy Quick Start Manual preview
ACE Easy
Бренд: ACE INSTRUMENTS Страницы: 2
TapFlo DT Series Original Instruction preview
DT Series
Бренд: TapFlo Страницы: 35
DANA DT Series Assembly Instructions Manual preview
DT Series
Бренд: DANA Страницы: 8
2E PSE801 User Manual preview
PSE801
Бренд: 2E Страницы: 6
Cambro Camshelving Quick Start Manual preview
Camshelving
Бренд: Cambro Страницы: 6
Nitecore NPL20 User Manual preview
NPL20
Бренд: Nitecore Страницы: 4
Palmer PGA-04 ADIG-LB Quick Start Manual preview
PGA-04 ADIG-LB
Бренд: Palmer Страницы: 2
TEC DG-1000 Quick Manual preview
DG-1000
Бренд: TEC Страницы: 6
U Technology Magic Series Installation Manual preview
Magic Series
Бренд: U Technology Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды