Parker SciLog FilterTec Plus Скачать руководство пользователя | Manualshive

Страница: 48 / 72

background image

48

5.3 Setup: Test Mode:

Test Mode

provides the ability to test the inputs and outputs (I/O’s) of the FilterTec Plus outside

of the normal operational modes. Upon pressing Select, the FilterTec Plus will attempt Scale
Initialization. If it passes, the next Test appears. If it fails, press any key and the next Test
appears. Use the Star (*) button to move between tests.



Motor

: This tests the motor. Use the Rate/Pressure button to change the motor speed. Use

the Run / Stop buttons, and the CW / CCW keys to exercise the motor. The encoder
pulses/second is displayed.



Keypad

: This tests the keypad. Press the buttons in any order, and an appropriate number

is displayed. Left to right, top to bottom, they are numbered 1 through 0, the Star key
passes if it moves to the next test.



Scale

: If a scale is connected and is communicating properly, the value here will match that

of the scale.



Pressure

: If SciPres Disposable Pressure Sensors are connected, they will display the

measured pressure, P1, P2, P3. By pressing the A, B, or C keys, the sensors may be
zeroed. If there is no sensor connected,

--.-

will be displayed.



Temperature

: If a SciTemp Disposable Pressure Sensor is connected, the measured

temperature in

⁰

C will be displayed. If no sensor is connected, 0.0 is displayed.



Valves

: If Valve V or W is connected, press the A or B button to test them.



Analog

: Displays the analog value for Channels 1, 2 and 3 based upon input and Hi/Lo

range settings.



TTL Switches:

By using Left and 1/0 to change the BIT setting, the TTL outputs may be

tested. You must have a DMM connected to measure the voltage, it will be 0.0 if Switch is
set to 0, and 5.0 Vdc if set to 1. (display is 1234 if all are high, 0000 if all are low)

- SETUP – TEST MODE
UP DOWN SELECT

SCALE INTITIALIZATION

Please Wait

SELECT

STAR KEY

- TEST- 10% 00000
CW CCW

- TEST- KEYPAD

- TEST- SCALE
0.00 0.00 0.00

- TEST- PRESSURE
00.0

00.0 00.0

SCALE ERROR

Hit any key

- TEST- VALVES
V1

W1

- TEST- TEMPERATURE
0.0

STAR KEY

STAR KEY

STAR KEY

STAR KEY

- TEST- ANALOG
0.0

0.0

0.0

Sw – 1234 – BIT 1
LEFT

1/0

Select

STAR KEY

STAR KEY

«
...
46
47
48
49
50
...
»

Содержание SciLog FilterTec Plus









































































Отзывы:

Нет отзывов

Похожие инструкции для SciLog FilterTec Plus

Бренд: Pall Страницы: 51

Бренд: ZAMST Страницы: 21

Бренд: 3M Страницы: 2

Бренд: KaVo Страницы: 13

Бренд: vc999 Страницы: 52

Бренд: Olsen Страницы: 56

Бренд: Waterous Страницы: 5

Бренд: 3TECH Страницы: 32

Бренд: 4EVAC Страницы: 15

BODY ARMOR PRO TERM

Бренд: Darco Страницы: 6

Бренд: Ocmis Irrigazione Страницы: 100

Бренд: Omlet Страницы: 60

RIDA qLine ZG2601

Бренд: R-Biopharm Страницы: 23

Бренд: TDR Страницы: 8

Бренд: VelociRAX Страницы: 4

Бренд: ABM Страницы: 17

Heart Guardian AED

Бренд: Radian Страницы: 36

UltraVent XS Plus 6 2/3 E

Бренд: Rational Страницы: 220

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды