Parker SciLog FilterTec Plus Скачать руководство пользователя

Страница: 10 / 72

FilterTec Plus Balance



Balances with capacity of 8,100 grams x 0.1 g resolution with all FilterTec Plus models.



Larger balances available upon request. Contact Parker Customer Service.

FilterTec Plus Software

Main menu with five operational modes:



Constant Rate Mode

: Pumps at a user defined rate, and can switch to a user defined

pressure with five, user-definable alarms, in particular, the

Pmaintain

Alarm that

switches from Rate to Pressure control.



Constant Pressure Mode

: Pressure controlled flow rate is varied to maintain a user-

defined pressure by modulating the Feed Rate, with five, user-definable alarms.



Programmable R-P Mode:

Programmable step-by-step variable Rate and Pressure

control, with access to a six-way valve.



Setup Mode

: Selection of user preferences and interface options.



Manual Mode

: Manual control of motor speed and will monitor one pressure, no alarms.



Can change the Rate or Pressure on the fly

. This is a very useful tool in determining

the optimum parameters for your process.



Optimizes DEF Applications:

Dead End, Direct Flow, or Normal Flow Filtration.



Implement Filterability Studies

, in addition to Filter Size Determinations.

Documentation Software for PC

SciDoc Excel Spreadsheet with custom macros and WinWedge interface software for data
compilation. Sent to you ready to use.



Complete process analysis with graphing of data.



Real-time verification and documentation of process parameters.



Includes graphs of:



Feed Rate (FF), Collection Rate (C1) and Pressure (P1) vs. Time



Collection Rate (C1) and Filtrate Quantity (Q1) vs. Time



T/W vs. Time, Vmax

Display, Printout and Excel Abbreviations:

= Military Time, HH:MM:SS

= Feed Rate, ml/min

= Run Time, 00:00:00 at START

= Cumulative Feed Volume, ml

= Filtrate Quantity collected

= Collection Rate, gr/min

= Pressure at Sensor 1, psi, bar or kpa

= Clockwise Pump Direction

= Pressure at Sensor 2, psi, bar or kpa

CCW

=Counter Clockwise Pump Direction

= Pressure at Sensor 3, psi, bar or kpa

= Pump Status, START, RUN, etc.

= Alarm, e.g. CV Cumulative Volume Alarm

=1, Cumulative Volume Alarm is “OFF”

=4, High Pressure Alarm is “Pmaintain”

=2, Run Time Alarm is “ALERT ONLY”

=1, Low Pressure Alarm is “OFF”

=2, Low Flow Alarm is “ALERT ONLY”

=3, Filtrate Weight Alarm is “PUMP STOP”

= Response Factor

Содержание SciLog FilterTec Plus









































































Результаты поиска

Содержание SciLog FilterTec Plus

Отзывы:

Похожие инструкции для SciLog FilterTec Plus

Бренды по названию

Популярные бренды

Parker SciLog FilterTec Plus, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание SciLog FilterTec Plus

Отзывы:

Похожие инструкции для SciLog FilterTec Plus

Бренды по названию

Популярные бренды