Parker SciLog FilterTec Plus Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 72

Parker SciLog FilterTec Plus Скачать руководство пользователя страница 52

52

5.7 Setup: Pressure Sensor

Pressure Sensor

is used to configure settings related to the SciPres Disposable Pressure

Sensors. The following can be configured; Range, Units, Source (control and alarms), Filter
(signal noise) and Zero/Span.



Range:

Set the overall pressure range, the Default is 60.0 psi, and is the maximum.

Changing this setting requires re-calibration of the sensor signals.



Units:

Select between Psi, Bar, and KPA. Default = Psi.



Source:

Controls the source pressure sensor for control in Constant Pressure Mode, and

for all pressure alarms. Select between P1, P2 or P3. Default = P1



Zero:

Used to “Zero” the sensors to establish the zero offset cause by the circuitry and any

inherent hydraulic pressure in your tubing beyond the pump head. Connect the sensor, and
remove any pressure from the system. Select the sensor, P1, P2 or P3 and press “Zero”.
You are prompted to confirm the action. “Span” should not be used on a routine basis, as it
sets the max input value. NOTE: Do not Zero P1, P2 or P3 unless a sensor is connected.
The display should read “--.-“ with no sensor connected. If it reads 0.0 in this state, connect
the sensor and re-zero it.



Filter:

This feature filters out the pulsations in the pressure signal due to the peristaltic

nature of the pump head. This provides better control and easier to read values, as
well as improved graphed data. Select from 1 to 7, 1 = no signal filter, 7 = maximum filter.
Default = 4.

- SETUP-PRESS.SENSOR
UP DOWN SELECT

PRESS RANGE: 60.0
UP DOWN SELECT

PRESSURE: RANGE
UP DOWN SELECT

PRESSURE UNITS: PSI
UP DOWN SELECT

PRESSURE: UNITS
UP DOWN SELECT

PRESS SOURCE: P1
UP DOWN SELECT

PRESSURE: SOURCE
UP DOWN SELECT

PRESSURE: ZERO
P1 P2 P3

PRESSURE: ZERO
UP DOWN SELECT

PRESS FILTER: 4
UP DOWN SELECT

PRESSURE: FILTER
UP DOWN SELECT

PRESSURE: 1 0.0
ZERO SPAN EXIT

SELECT

DOWN

DOWN

DOWN

DOWN

P1

«
...
50
51
52
53
54
...
»

Содержание SciLog FilterTec Plus









































































Отзывы:

Нет отзывов