manualshive.com logo in svg

Parker SciLog FilterTec Plus, Инструкция по установке, эксплуатации и обслуживанию

«Parker SciLog FilterTec Plus» - продукт, который необходим для обеспечения чистоты в вашей системе. Перед установкой, эксплуатацией и обслуживанием убедитесь в правильном использовании, скачав руководство по установке, эксплуатации и обслуживанию с manualshive.com. Это руководство доступно для бесплатного скачивания.

Поделиться
Скачать
background image

 

 

34

3.1 CONSTANT PRESSURE: Alarm Limits 

SUMMARY:

 This section allows you to assign limiting values for several different alarm 

conditions: 

Cumulative Volume (CV)

 in milliliters; 

Hi Temperature

 in 

⁰

C; 

Run Time (RT)

 in 

Hours: Minutes; 

Lo-Pressure (LP)

 (monitor system leakage) in psi; 

Lo-Flow (LC)

 (pump will 

stop when collection rate falls below this limit) in ml/min.; 

Filtrate Quantity (FQ) 

in grams. 

Note: 

The alarm condition is triggered when the alarm limit is achieved. 

Alarms are not mutually 

exclusive. You may select any combination of alarms.  

For critical alarms you may want the FilterTec Plus pump to stop (

Pump Stop

). For less critical 

alarm conditions you may want to choose an auditory alarm (

Alarm Only

).  

NOTE:

 The Lo-Pressure alarm is directly related to the Source chosen in SETUP: Press. 

Sensor, Source, i.e. P1, P2, etc. 

Use 

“Up”

 and 

“Down”

 keys, then press 

“Select” 

to implement selection. 

Cumulative Volume (CV): 

This alarm setting represents the total volume of process solution 

that is delivered through your filtration device when no balance is in use. 

Use the Filtrate 

Weight Alarm for this when a balance is in use!

 For example: if you set the 

Cumulative 

Volume Alarm

 to 10,000ml or 10 liters, the FilterTec Plus will either alarm and / or stop the 

pump when 10 liters of solution has been delivered through the filtration device. 

 

Hi-Temp

 

(HT):

 Used to monitor the temperature of the process solution, this will stop the pump 

at the set limit. Default = 35.0 

⁰

C

 

Run Time (RT):

 This alarm setting allows you to set a timer for the filtration of your process 

solution. For example, if you set the 

Run Time Alarm

 to 01:30, then the FilterTec Plus will 

provide you with an auditory alarm and / or stop the pump after one (1) hour and thirty (30) 
minutes have passed. This allows you to define the processing time, i.e. the time required to 
obtain a desired filtrate yield.

  

Lo-Pressure (LP):

 Typically set 3-5 psi units below the 

Pump Pressure

 setting. The Lo-

Pressure Alarm is triggered when a sudden filter backpressure drop occurs after rising above 
this setting. Such a change in the filter backpressure usually indicates a system leak, i.e. pump 
tubing has slipped off the filter connection. 

 

Lo-Flow (LC): 

For constant pressure filtration, this represents a critical alarm condition, and 

should be set to 

Pump Stop

 in Low-Flow Alarm Enable. In this operational mode, the FilterTec 

Plus will detect any filter backpressure increases in the source pressure sensor (due to slow 
filter plug-up) and automatically decrease the feed rate to maintain the selected 

Pump 

Pressure

 setting (see 3.17). The Lo-Flow parameter (ml/min) represents lowest pump rate 

before the pump shuts down. The Lo-Flow parameter should be set just below your desired 
minimum collection rate. 

 

Filtrate Qty. (FQ): 

The FilterTec Plus comes with a top-loading balance. Enter the filtrate weight 

(grams) that you want to collect, and the FilterTec Plus will either alarm or stop the pump when 
the desired weight has been collected. Set this value to zero if you do not wish it to trigger 
during normal use. The maximum value is 99,999 gm. (100Kg). 

 

NOTE: This alarm must be enabled in at least “alarm only” mode in order for the Q1 
(Filtrate Weight) to be obtained or displayed. 

Содержание SciLog FilterTec Plus









































































Отзывы:

Нет отзывов

Похожие инструкции для SciLog FilterTec Plus

BACtrack VIO User Manual preview
VIO
Бренд: BACtrack Страницы: 13
Badgematic FLEXI Manual preview
FLEXI
Бренд: Badgematic Страницы: 28
BACtrack Select S80 Product Specifications preview
Select S80
Бренд: BACtrack Страницы: 2
MADRIX STELLA Quick Start Manual & Technical Manual preview
STELLA
Бренд: MADRIX Страницы: 28
BACTcontrol microLAN Software Manual preview
microLAN
Бренд: BACTcontrol Страницы: 28
Danfoss iSave 21 User Manual preview
iSave 21
Бренд: Danfoss Страницы: 106
Gardner Bender CP2000 Instruction Sheet preview
CP2000
Бренд: Gardner Bender Страницы: 8
NARIKA M1-S Instruction Manual preview
M1-S
Бренд: NARIKA Страницы: 2
Nectar Pacer Using Manual preview
Pacer
Бренд: Nectar Страницы: 46
Neauvia PLASMA IQ Training Manual preview
PLASMA IQ
Бренд: Neauvia Страницы: 17
Rational iCombi Pro Original Installation Manual preview
iCombi Pro
Бренд: Rational Страницы: 16
Waters Xevo TQD Operator'S, Overview And Maintenance Manual preview
Xevo TQD
Бренд: Waters Страницы: 250
Waters ACQUITY UPLC Overview And Maintenance Manual preview
ACQUITY UPLC
Бренд: Waters Страницы: 141
gbo ULTRATHERM 908i User Manual preview
ULTRATHERM 908i
Бренд: gbo Страницы: 32
Dantel 49009 Installation & Operation Manual preview
49009
Бренд: Dantel Страницы: 6
Zero 88 ECLIPSE Operator'S Manual preview
ECLIPSE
Бренд: Zero 88 Страницы: 22
Yaasa Illuminator Operating Instructions Manual preview
Illuminator
Бренд: Yaasa Страницы: 20
Sable 30K Directions For Use Manual preview
30K
Бренд: Sable Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды