Parker SciLog FilterTec Plus Скачать руководство пользователя

Страница: 47 / 72

5.2 Setup: Clock

Clock

is used to set the Date and Time in the FilterTec Plus real time clock, and control the

displayed and output time format.



Time of Day:

Press Select and use the Incr. and Decr. buttons to set the current time in 24

hour format. This should be preset by the factory prior to shipping.



Print Enable:

Controls displayed and output time. Choose between Time of Day and

Relative Time. Time of Day yields current time, and Relative Time starts at 00:00:00 at the
beginning of a processing run. Default = Time of Day.



Year:

Press Select and use Incr. and Decr. to set the current year.



Day of Month:

Press Select and use Incr. and Decr. to set the current day of the month.



Month

: Press Select and use Incr. and Decr. to set the current month.

SELECT

- CLOCK- TIME OF DAY
UP DOWN SELECT

- SETUP - CLOCK
UP DOWN SELECT

TIME: 12:00
INCR DECR SELECT

- CLOCK- DAY
UP DOWN SELECT

- CLOCK- YEAR
UP DOWN SELECT

- CLOCK- PRINT ENABLE
UP DOWN SELECT

- CLOCK- MONTH
UP DOWN SELECT

DOWN

PRINT: TIME OF DAY
INCR DECR SELECT

YEAR: 2009
INCR DECR SELECT

DAY OF MONTH 12
INCR DECR SELECT

MONTH: 8
INCR DECR SELECT

Содержание SciLog FilterTec Plus









































































Результаты поиска

Содержание SciLog FilterTec Plus

Отзывы:

Похожие инструкции для SciLog FilterTec Plus

Бренды по названию

Популярные бренды

Parker SciLog FilterTec Plus, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание SciLog FilterTec Plus

Отзывы:

Похожие инструкции для SciLog FilterTec Plus

Бренды по названию

Популярные бренды