Parker SciLog FilterTec Plus Скачать руководство пользователя

Страница: 18 / 72



Mettler: PGS, PM, Viper Models

P/N: 080-067PGS



Ohaus: GT, “Precision Advanced”

P/N: 080-066

& “Explorer” & “Voyager” Models



Ohaus: IP Series High Capacity

P/N: 080-067



Ohaus: Adventurer Pro Series

P/N: 080-067PGS



Sartorius: Most Series Balances

P/N: 080-068



In the FilterTec Plus

Setup: Scale, Scale2 and Scale3

, select the scale

manufacturer; the FilterTec Plus will automatically implement the correct
communications parameters.

Check that the proper communications

parameters are also implemented in the scale you are using.



Pressure Sensor Ports:

RJ11 Telephone jacks for the SciPres Disposable Pressure

Sensors, labeled “P1”, “P2”, and “P3”. The disposable pressure sensors plug into these
jacks using the included cables.



Temperature Probe Port:

The SciTemp Disposable Temperature Senor connects to

this port with a twist-lock connector cable. Temperature is measured in degrees Celsius.



Valve V Port:

Used in conjunction a 6-way Selector Valve (P/N: 080-510) in RP

Programmable Mode.



USB Port:

Used for connection to a PC, providing a Com Port. Can be used for data

collection as an alternative to the Printer port. The driver is included on the CD that
contains this manual.



Ethernet Port:

Used for connection to the FilterTec Plus via a LAN. IP Address, Subnet

Mask, and Gateway are configured in the Setup menu. The communication protocol is
Modbus TCP/IP, and a list of registers is in the appendix of this manual. (When
available.)

Содержание SciLog FilterTec Plus









































































Результаты поиска

Содержание SciLog FilterTec Plus

Отзывы:

Похожие инструкции для SciLog FilterTec Plus

Бренды по названию

Популярные бренды

Parker SciLog FilterTec Plus, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание SciLog FilterTec Plus

Отзывы:

Похожие инструкции для SciLog FilterTec Plus

Бренды по названию

Популярные бренды