Parker SciLog FilterTec Plus Скачать руководство пользователя | Manualshive

Страница: 3 / 72

background image

3

Precautions

READ this manual BEFORE operating or servicing this equipment.

FOLLOW these instructions carefully.

SAVE this manual for future reference.

DO NOT allow untrained personnel to operate, clean, inspect, service or tamper with
this equipment.

ALWAYS DISCONNECT this equipment from the power source before cleaning or
performing maintenance.

CALL Parker for parts, information and service.

IF power cord is lost or damaged, contact Customer Service to obtain a new one. Do not
replace it on your own.

WARNING

DISCONNECT ALL POWER TO THIS UNIT BEFORE INSTALLING,
SERVICING, CLEANING OR REMOVING THE FUSE. FAILURE TO DO
SO COULD RESULT IN BODILY HARM AND/OR PROPERTY
DAMAGE.

CAUTION

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC
SENSITIVE DEVICES.

WARNING

ONLY PERMIT QUALIFIED PERSONNEL TO SERVICE THIS
EQUIPMENT. EXERCISE CARE WHEN MAKING CHECKS, TEST AND
ADJUSTMENTS THAT MUST BE MADE WITH POWER ON. FAILING
TO OBSERVE THESE PRECAUTIONS CAN RESULT IN BODILY
HARM.

WARNING

FOR CONTINUED PROTECTION AGAINST SHOCK HAZARD,
CONNECT TO PROPERLY GROUNDED OUTLET ONLY. DO NOT
REMOVE THE GROUND PRONG.

IF the power cord is lost or damaged, contact Customer Service to obtain a new one. Do
not replace it on your own.

«
1
2
3
4
5
...
»

Содержание SciLog FilterTec Plus









































































Отзывы:

Нет отзывов

Похожие инструкции для SciLog FilterTec Plus

Бренд: Tabi Страницы: 8

Бренд: Dabi Atlante Страницы: 102

Бренд: Federal Signal Corporation Страницы: 2

Бренд: Harman Kardon Страницы: 7

Бренд: GE Страницы: 212

Бренд: Laserworld Страницы: 8

Бренд: Laserworld Страницы: 6

Бренд: LaserLiner Страницы: 56

Бренд: LaserLiner Страницы: 54

Бренд: M-Audio Страницы: 12

Бренд: M-Audio Страницы: 64

Бренд: M-Audio Страницы: 16

Бренд: M-Audio Страницы: 4

Бренд: M-Audio Страницы: 52

Бренд: Opvimus Страницы: 50

Бренд: ZAMST Страницы: 14

Бренд: Future Artist Страницы: 42

Бренд: Moog Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды