manualshive.com logo in svg

Parker SciLog FilterTec Plus, Инструкция по установке, эксплуатации и обслуживанию

«Parker SciLog FilterTec Plus» - продукт, который необходим для обеспечения чистоты в вашей системе. Перед установкой, эксплуатацией и обслуживанием убедитесь в правильном использовании, скачав руководство по установке, эксплуатации и обслуживанию с manualshive.com. Это руководство доступно для бесплатного скачивания.

Поделиться
Скачать
background image

 

 

42

4.2 PROGRAMMABLE R-P: Alarm Limits 

SUMMARY:

 This section describes assigning limiting values for several alarm conditions: 

Cumulative Volume

 in milliliters; 

Hi-Temperature 

in 

⁰

C; 

Lo-Pressure

 (monitor system 

leakage) in psi; 

Hi-Pressure

 (Monitor filter plug-up) in psi; 

Lo-Flow

 (pump will stop when pump 

feed rate falls below this limit) in ml/min.; 

Filtrate Quantity 

in grams.  

The alarm condition is triggered when the alarm limit is exceeded. 

Alarms are not mutually 

exclusive. You may select any combination of alarms.  

For critical alarms you may want the FilterTec Plus pump to stop (

Pump Stop

). For less critical 

alarm conditions you may want to choose an auditory alarm (

Alarm Only

). 

PLEASE NOTE

: The High and Lo-Pressure alarms are directly related to the Source chosen in 

SETUP: Press. Sensor, Source, i.e. P1, P2, etc. 

Use 

“Up”

 and 

“Down”

 keys to make a selection, then press 

“Select” 

to implement that 

selection. 

Cumulative Volume (CV): 

This alarm setting represents the total volume of process solution 

that is pumped through your filtration device when a balance is not in use. 

When using a 

balance, set this limit in the Filtrate Weight Alarm!

 For example: if you set the 

Cumulative 

Volume Alarm

 to 10,000ml or 10 liters, the FilterTec Plus will either alarm and / or stop the 

pump when 10 liters has been pumped through the filtration device. 

 

Hi-Temp

 

(HT):

 Used to monitor the temperature of the process solution, this will stop the pump 

at the set limit. Default = 35.0 

⁰

C

 

Lo-Pressure (LP):

 Typically set 3-5 psi units below the desired pressure setting in the step-by-

step instructions. The Lo-Pressure Alarm is triggered when a sudden filter backpressure drop 
occurs after rising above this setting. Such a change in the filter backpressure usually indicates 
a system leak. 

Hi-Pressure (HP): 

For most applications, this represents a critical alarm condition. If this is the 

case choose 

Pump Stop

. Make sure you stay below the pressure limit specified by the filter 

manufacturer. I.e., if your filter specifies an upper pressure limit of 25 psi, you might set your 

Hi-

Pressure Alarm

 to 20 psi. The FilterTec Plus will alarm and stop the pump when the filter 

backpressure exceeds 20 psi. If you have chosen 

Pmaintain

, this is the value at which the 

system will switch from a Rate control method to the Pressure control method and maintain that 
pressure.

 

Lo-Flow (LC): 

For constant pressure filtration, this represents a critical alarm condition and 

should be set to 

Pump Stop

 in Lo-Flow Alarm Enable. In this operational mode, the FilterTec 

Plus will detect any filter backpressure increases in the source pressure sensor (due to slow 
filter plug-up) and automatically decrease the rate to maintain the desired pressure setting in the 
step-by-step instructions. The Lo-Flow value (ml/min) represents lowest pump rate before the 
pump shuts down. 

 

Filtrate Qty. (FQ): 

The FilterTec Plus comes with a top-loading balance. Enter the filtrate 

quantity (grams) that you want to collect, and the FilterTec Plus will either alarm or stop the 
pump when the desired filtrate / permeate weight has been collected. Set this value to zero if 
you do not wish it to trigger during normal use.  

Note: This alarm must be enabled in at least “alarm only” mode in order for Q1 (Filtrate 
Quantity) to be obtained or displayed. 

Содержание SciLog FilterTec Plus









































































Отзывы:

Нет отзывов

Похожие инструкции для SciLog FilterTec Plus

THORLABS Vytran LFS4100 User Manual preview
Vytran LFS4100
Бренд: THORLABS Страницы: 44
GE b30 User'S Reference Manual preview
b30
Бренд: GE Страницы: 242
GE ATS1290 Instruction Manual preview
ATS1290
Бренд: GE Страницы: 24
Balanced Body Allegro How To Assemble preview
Allegro
Бренд: Balanced Body Страницы: 3
p-light Maxi Installation And Instructions For Use preview
Maxi
Бренд: p-light Страницы: 28
Fayat BOMAG BW 100 ADM-5 Operating Instruction preview
BOMAG BW 100 ADM-5
Бренд: Fayat Страницы: 216
B medical systems MT100 Instructions For Use Manual preview
MT100
Бренд: B medical systems Страницы: 28
IEMCA KID 80 Manual For Use And Maintenance preview
KID 80
Бренд: IEMCA Страницы: 82
IEMCA KID 80-IV Touch Instruction Manual preview
KID 80-IV Touch
Бренд: IEMCA Страницы: 122
Calrec ARGO Installation & Technical Manual preview
ARGO
Бренд: Calrec Страницы: 92
Velleman K4401 Illustrated Assembly Manual preview
K4401
Бренд: Velleman Страницы: 16
Velleman VTTEST11 Manual preview
VTTEST11
Бренд: Velleman Страницы: 11
rbd instruments IG2 Manual preview
IG2
Бренд: rbd instruments Страницы: 18
Bartscher B5000 Manual preview
B5000
Бренд: Bartscher Страницы: 20
Bartscher 6640 Original Instruction Manual preview
6640
Бренд: Bartscher Страницы: 24
H&S 6118 Operator'S Manual preview
6118
Бренд: H&S Страницы: 32
Eaton Cutler-Hammer ATC-300 Instruction Booklet preview
Cutler-Hammer ATC-300
Бренд: Eaton Страницы: 32
V&P Scientific SpinVessel 650ml Operating Instructions Manual preview
SpinVessel 650ml
Бренд: V&P Scientific Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды