Parker SciLog FilterTec Plus Скачать руководство пользователя | Manualshive

Страница: 23 / 72

background image

23

manner. This is accomplished by entering step-by-step instructions from the FilterTec Plus front
panel buttons. You can enter and control by using Run, Stop, Time, Direction, R-Step, R-Scan,
P-Step, P-Scan, V, and W commands to have the system perform changing rates and
pressures, even rotary selector valve positions for switching buffers or collection vessels. A
sample program is included in this manual. All alarms used in CONSTANT RATE and
CONSTANT PRESSURE Modes except Run Time are available in PROGRAMMABLE R-P
Mode.

SETUP:

This operational mode allows you to select various user preferences and interface

options. The

Setup: Scale

submenu provides electronic balance options. Balances that can

interface with the FilterTec Plus must have bi-directional serial communication, and NOT have
internal calibration or be “delta-range” models. Many Mettler, Ohaus, and Sartorius balances
can be used. The

Setup: Clock

submenu allows the user to set the time and date used in the

display. The

Setup: System Test

submenu allows checkout of FilterTec Plus outputs and

requires purchase of a special set of connectors to perform the test.

Setup:

Test Mode

provides an additional mode to test the I/O’s independently.

Setup: Ethernet

is used to set the

IP Address, Subnet Mask, and Gateway for Modbus TCP/IP communications.

Setup: Printer

is

used for setting up the printer/PC communications parameters as well as print time interval and
the print delay.

Setup: Analog

defines the ranges, alarms and limits for the three analog

channels available for data acquisition and reporting of 4-20 ma signals from detectors
equipped with analog outputs.

Setup: Temperature

allows the input of an offset value if needed

for the temperature input.

Setup: Press. Sensor

is used to zero the pressure sensors, set the

units (psi, bar, kpa), and choose the source for the pressure control and alarms.

Setup: Pump

allows you to set various pump user preferences, most importantly the Motor RPM.

Setup:

Scale2

and

Scale3

are similar to Scale mentioned above.

MANUAL:

Allows manual control of pump speed and direction, and will display the value of

sensor P1. This is very useful for initial testing to determine flow rate / pressure settings.

NOTE:

CONSTANT RATE, CONSTANT PRESSURE, and PROGRAMMABLE R-P mode

Alarms and Printer parameters are not functional in the Manual mode.

«
...
21
22
23
24
25
...
»

Содержание SciLog FilterTec Plus









































































Отзывы:

Нет отзывов

Похожие инструкции для SciLog FilterTec Plus

Бренд: Pall Страницы: 51

Бренд: ZAMST Страницы: 21

Lab companion SI-300

Бренд: Jeio tech Страницы: 69

IP Video Test Option HST-3000

Бренд: JDS Uniphase Страницы: 4

Бренд: Jct Страницы: 16

Бренд: Keithley Страницы: 79

Бренд: Kayakpro Страницы: 17

Бренд: Yoshitake Страницы: 11

Бренд: Maeda Страницы: 276

Бренд: Octane Fitness Страницы: 20

Бренд: Oceaneering Страницы: 27

Бренд: Quincy Страницы: 31

Lyme FIA Sofia 2

Бренд: Quidel Страницы: 49

Бренд: Quest Leisure Products Страницы: 12

Бренд: R&S Страницы: 371

Бренд: R.M. Young Страницы: 9

Бренд: Teac Страницы: 44

Бренд: Te Pari Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды