Parker SciLog FilterTec Plus Скачать руководство пользователя

Страница: 5 / 72

Table of Contents

Precautions .................................................................................................................... 3

Standards: ..................................................................................................................... 7

Installation & Start-Up: ................................................................................................. 7

Maintenance & Cleaning: .............................................................................................. 7

Introduction: .................................................................................................................. 7

FilterTec Plus Maintenance .......................................................................................... 7

FilterTec Plus System Specifications: ......................................................................... 9

Installation of the USB Driver: ................................................................................... 11

Part A: FilterTec Plus Hardware ................................................................................. 12

1.0 Overview: ................................................................................................................ 15

2.0 Front Panel: Data Entry & Display ........................................................................... 16

3.0 Back Panel: Interface Options ................................................................................. 17

4.0 Pressure Sensor Installation: .................................................................................. 20

Part B: FilterTec Plus



Software ............................................................................... 21

1.0 Software Overview: Main Menu............................................................................... 22

2.0 CONSTANT RATE Mode: Constant Rate/ Pressure Filtration. ............................... 25

2.1 Pump Re-calibration: ........................................................................................ 27

2.2 CONSTANT RATE Mode: Alarm Limits ............................................................ 28

3.0 CONSTANT PRESSURE: Constant Pressure Filtration .......................................... 32

3.1 CONSTANT PRESSURE: Alarm Limits ............................................................ 34

4.0 PROGRAMMABLE R-P: How to generate a PROGRAMMABLE R-P program. ..... 37

4.1 PROGRAMMABLE R-P: Setup ......................................................................... 40

4.2 PROGRAMMABLE R-P: Alarm Limits .............................................................. 42

5.0 Setup ....................................................................................................................... 44

5.1 Setup: Scale ..................................................................................................... 45

5.11 Ohaus Adventurer Pro Balance Parameters: .................................................. 46

5.2 Setup: Clock ..................................................................................................... 47

5.3 Setup: Test Mode: ............................................................................................. 48

5.4 Setup: Ethernet ................................................................................................. 49

5.5 Setup: Printer .................................................................................................... 50

5.6 Setup: Analog ................................................................................................... 51

5.7 Setup: Pressure Sensor .................................................................................... 52

5.7 Setup: Pressure Sensor, Calibration ................................................................. 53

Содержание SciLog FilterTec Plus









































































Результаты поиска

Содержание SciLog FilterTec Plus

Отзывы:

Похожие инструкции для SciLog FilterTec Plus

Бренды по названию

Популярные бренды

Parker SciLog FilterTec Plus, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание SciLog FilterTec Plus

Отзывы:

Похожие инструкции для SciLog FilterTec Plus

Бренды по названию

Популярные бренды