Parker SciLog FilterTec Plus Скачать руководство пользователя

Страница: 9 / 72

FilterTec Plus System Specifications:

Mechanical:



Dimensions:

Width: 5.75 in (14.6cm); Height: 8.5 in (212.6); Depth: 11in (27.9)



Weight:

14 lbs (6.4kg)



Enclosure:

Aluminum / Steel; Corrosion Resistant, Recessible Handle



Pump Head / Motor Options:



Three Masterflex Easy-Load II (77201-60) adjustable occlusion pump heads with 8
RPM motor

, accommodates thin-walled (0.060”) pump tubing: #13, 14, 16, 25, and #17.

Pump Rate Range: 0.03 to 24.3 ml/min.



Three Masterflex Easy-Load II (77201-60) adjustable occlusion pump heads with 160-
RPM motor,

accommodates thin-walled (0.060”) pump tubing: #13, 14, 16, 25, and #17.

Pump Rate Range: 0.5 to 554 ml/min.



Three Masterflex Easy-Load II (77201-62) adjustable occlusion pump heads with 600-
RPM motor,

accommodates thick-walled (0.090”) pump tubing: #15, 24 and #35. Pump

Rate Range: 59 to 2,258 ml/min.



Pressure Sensors:

Accommodates up to three (3) SciPres ™ Disposable pressure

sensors: P1, P2, and P3. Pressure control is achieved by modulating pump output. The
user selects P1, P2 or P3 as the controlled pressure.



Pressure Displayed

with a resolution of 0.1 psi; choice of

bar, psi, kpa



Pressure Range:

The default pressure range of the sensors is

0-60psi

, and is calibrated at

the factory. Most peristaltic pumps generate pressures up to 40 psi. If you have need for
higher pressures, contact Parker Customer Service for assistance.

Electrical



Power:

90 - 264 V

, 47-63 Hz, 150 VA, listed Class 2 switching power supply; double

fused: 1A-T, 250V (CE: IR35A 250V



Battery:

CR1220, used to support the internal clock only, not user serviceable.



Motor:

Choice of three (3) motors: 8, 160 and 600 RPM at 30V

, 3.8 Amperes, Variable

Pump Speed optically encoded, servo-controlled motors.



Encoder:

100 lines/rev for 600-RPM motor. 120 lines per/rev for 8 & 160-RPM motors.



I/O Ports:



“

Printer

”, Female DB9 connector for data collection with Printer or PC.



“

”, “

”, Male DB9 connector for RS-232 connections to an electronic scale.



“

External I/O

”, Female DB37 connector used for remote On/Off control of FilterTec Plus via

footswitch, or for Analog interface with 4-20 ma sources, A1, A2, A3.



“

”, Female DB15 connector, Not utilized on FilterTec Plus.



“

Temperature

”, 2 pin Conxall connector for SciTemp™ disposable Temperature Sensor.



“

P1, P2, P3

”, RJ11 connectors used for SciPres disposable Pressure Sensors.



“

USB

”, USB-A connector, used for RS-232 data collection with a PC.



“

Ethernet

”, RJ-45 connector, not enabled.



Display:

Two-line LCD, 20 characters each, back-lit.



Data Entry

: Membrane keyboard with auditory feedback.

Environmental



Temperature range: 4 to 40





Altitude: up to 2000 Meters



Indoor, dry environments only, clean-up is wipe down only.(IP 20)



Relative humidity: 0-95%



Voltage fluctu/- 10%



Pollution degree: 2

Содержание SciLog FilterTec Plus









































































Результаты поиска

Содержание SciLog FilterTec Plus

Отзывы:

Похожие инструкции для SciLog FilterTec Plus

Бренды по названию

Популярные бренды

Parker SciLog FilterTec Plus, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание SciLog FilterTec Plus

Отзывы:

Похожие инструкции для SciLog FilterTec Plus

Бренды по названию

Популярные бренды